Iseki SZ330 SSM60 страница 47 Скачать руководство пользователя

Страница: 47 / 91

When the belt deflection is improper, correct in the follow-
ing procedure:

a. Loosen the lock nut and adjust bolt of the alternator.

b. Pull the alternator outward to apply more tension to

the belt. Tighten the lock bolt and adjust bolt temporar-
ily while pulling the alternator.

c. Check for the belt deflection to see if the tension is

proper. If so, tighten the lock nut and adjust bolt
securely.

IMPORTANT: When the belt is found to be defective,

ask your dealer for replacement.

9. ADJUSTMENT OF BRAKE

a. Step on the brake pedal,1, located on the right of the

step to its limit. Then, adjust the adjust bolt so that the
notch of the parking lever,2, locks at the third level.

b. Adjust the brake rod,4, with the parking brake so that

the space between the coils of the pair of brake
springs,5, is set to 0.9 mm (0.35 in).

c. Start the engine and drive the zero-turn mower for-

ward at a low speed. Step on the brakes and check if
the brakes are working evenly or not.

d. Stop the engine and make sure to lock the lock nuts,6,

of the brake rod.

DANGER:Please make sure that the engine is
turned off before adjusting the brakes.

ZERO TURN MOWER

0.9 mm (0.035 in)

ＬＨ

(1) Brake pedal

(4) Brake rod

(7) Rear axle

(2) Parking brake lever

(5) Brake spring

(8) Brake Assy

(3) Adjust bolt

(6) Lock nuts

FIG. 8-19

Содержание SZ330 SSM60




























































































Результаты поиска

Содержание SZ330 SSM60

Отзывы:

Похожие инструкции для SZ330 SSM60

Бренды по названию

Популярные бренды

Iseki SZ330 SSM60, Руководство по эксплуатации

Результаты поиска

Содержание SZ330 SSM60

Отзывы:

Похожие инструкции для SZ330 SSM60

Бренды по названию

Популярные бренды