manualshive.com logo in svg

Iseki SZ330 SSM60, Руководство по эксплуатации

Поделиться
Скачать
Iseki SZ330 SSM60 Скачать руководство пользователя страница 64

63

CHAPTER 10. TROUBLESHOOTING

6. ELECTRICAL ACCESSORIES

Troubles

Presumable causes

Remedies

･

Battery is not charged.

･

Melted slow-blow fuse

･

Defective wiring

･

Loose fan belt

･

Defective battery

･

Defective alternator

･

Locate and repair cause of

trouble, and install a new

slow-blow fuse.

･

Check wiring for loose

terminals and earth, and short

circuit. Repair defective parts.

･

Tighten belt as specified.

･

Correct loose terminals and

corroded parts, Otherwise, install 

a new battery.

･

Consult your dealers.

･

Moniotor lamps do not

light up.

･

Defective contact

･

Re-connect connector.

･

Fuel pump does not work.

･

Blown fuse

･

Defective fuel pump

･

Check the wiring and replace

the blown fuse with a new one.

･

Consult your dealers.

･

Fuel cut-off solenoid

does not work.

･

Blown fuse

･

Defective solenoid

･

Check the wiring and replace

the blown fuse with a new one.

･

Consult your dealers.

Содержание SZ330 SSM60




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды