Iseki SZ330 SSM60 страница 20 Скачать руководство пользователя | Manualshive

Страница: 20 / 91

background image

19

14. CAUTION LABELS & THEIR POSITIONS

•

Caution labels on the zero turn mower and the mower deck

The following labels are stuck on the zero turn mower and mower deck. You should of course read the caution
instructions in the manual. But never fail to read the labels on the zero turn mower and mower deck as well. Their
respective code numbers are also mentioned below, so order them from your deal if any of them are lost or dam-
aged.

CHAPTER 1. FOR SAFE OPERATION

１７０５−９０４−００４−０

１２°＋

１．

２．

ＳＴＯ

Ｐ

３．

1

2

(1)

Caution label

a. Read the manual thoroughly.
b. Shut off the engine and remove the starter key

before servicing or repairing the machine.

c. The negative terminal of the battery should be dis-

connected before servicing or repairing the machine.

d. When leaving the machine, apply the parking

brakes, shut off the engine, and remove the engine
key.

e. Risk of injury

Keep all safety devices such as guards, safety
switches, etc in place and working properly.

f. Risk of injury

Remove objects from around the machine that
could be thrown by blades and keep people away
from the machine before starting the machine.

g. Risk of running over a person

Watch behind before reversing the machine and
keep people from around the machine before start-
ing the machine.

h. Risk of running over a person

Don't allow any other person to ride on a wheel
fender or any place other than the driver's seat of
the machine.

i. Risk of overturning or crushing

Do not operate the machine in any place where it
could slip or tip over.

j. Risk of overturning or crushing

Avoid operating the machine on a steep slope.

(2)

Fuel label

Use diesel fuel only. No open flame.

１７０５−９０４−００４−０

１２°＋

１．
２．

ＳＴＯＰ

３．

«
...
18
19
20
21
22
...
»

Содержание SZ330 SSM60




























































































Отзывы:

Нет отзывов

Похожие инструкции для SZ330 SSM60

Бренд: Yard-Man Страницы: 24

Бренд: LawnMaster Страницы: 28

Бренд: MTD Страницы: 28

Бренд: SaMASZ Страницы: 41

Бренд: Ferris Страницы: 48

Бренд: Ozito Страницы: 14

Бренд: Snapper Страницы: 176

Бренд: Peco Страницы: 21

Бренд: Peco Страницы: 26

Бренд: IronCraft Страницы: 44

Бренд: Craftsman Страницы: 27

Бренд: Craftsman Страницы: 28

Бренд: Craftsman Страницы: 31

Бренд: Craftsman Страницы: 31

Бренд: Craftsman Страницы: 31

Бренд: Craftsman Страницы: 30

Бренд: Craftsman Страницы: 30

Бренд: Craftsman Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды