Iseki SZ330 SSM60 страница 71 Скачать руководство пользователя

Страница: 71 / 91

1. BEFORE OPERATION

CAUTION:
• Become familiar with haw to operate the

zero turn mower and understand safety
instructions by reading this manual careful-
ly.

• Make sure that all safety covers and guards

are installed in position.

• Make sure that the blade nuts are tightened

securely.

• Make sure that the belt is tensioned evenly

as specified.

• Before moving the zero turn mower into the

working site, check the whole area and get
rid of all obstacles such as stones, wood,
empty tins, bottles, wires, etc to assure safe
operation.

• Make sure that the mower operation will not

cause any injury to children, animals,
bystanders, or damage to trees, buildings,
etc.

• Check the place to mow for bumps, ditches,

mounds, steps, slopes, inclination, soft-
ness, water pools, etc. ahead of time to
avoid accidents such as turnover, fall, side-
sliding of the zero turn mower.

2. CUTTING HEIGHT ADJUSTMENT

a. Start the engine and raise the mower deck by the lift

lever,2.

b. Set to the trimming height by using the height adjust

dial,1.

c. Stop the engine.

d. Adjust the level of the front gauge wheel,2, and the

rear gauge wheel,3, to the trimming height set using
the height adjust dial.

IMPORTANT: Please make sure that there is a clear-

ance of 7 mm (0.3 inches) between the
ground and the gauge wheels.

(1) Heiget adjust dial

(2) Lift lever

(1) Spring clippin

(3) Real gauge wheel

(2) Front gauge wheel

ZERO TURN MOWER

CHAPTER 4. MOWER OPERATION

FIG. 4-1

FIG. 4-2

Содержание SZ330 SSM60




























































































Результаты поиска

Содержание SZ330 SSM60

Отзывы:

Похожие инструкции для SZ330 SSM60

Бренды по названию

Популярные бренды

Iseki SZ330 SSM60, Руководство по эксплуатации

Результаты поиска

Содержание SZ330 SSM60

Отзывы:

Похожие инструкции для SZ330 SSM60

Бренды по названию

Популярные бренды