Iseki SZ330 SSM60 Скачать руководство пользователя | Manualshive

Страница: 49 / 91

background image

48

12. ADJUSTMENT PHASE OF DRIVE CONTROL

LEVER

After adjusting the straight drive operation of the mower,
perform the following steps when the amount of depres-
sion of the left and right control levers are not the same.

a. Remove the boots,3, of both drive control levers,1.
b. Loosen the adjust bolts,2, and adjust the depression

of both drive control levers.

c. Re-install the boots to their original position.

DANGER:Please make sure that the engine is
turned off before adjusting the depression of
the control levers using the adjust bolt.

13. ADJUSTMENT CLEARANCE OF DRIVE CONTROL

LEVER

a. Remove the boots of both drive control levers.
b. Loosen the adjust bolts,3, to adjust the adjust plate.
c. Adjust the control levers so that their clearance is

about 35 mm (1.38 in). Tighten the adjust bolts.

d. Re-install the boots to their original position.

DANGER:Please make sure that the engine is
turned off before adjusting the adjust bolts.

Insufficient clearance in both left and right
control levers can lead to abnormal operation
of the zero-turn mower. Therefore, the clear-
ance limit prescribed above should be main-
tained.

14. INSPECTION OF WHEEL TIGHTEN ING BOLTS

AND NUTS

Check the wheel tightening bolts and nuts for looseness.
All loose bolts should be tightened to the specified level.

Specified tightening torque:

Rear wheel:

64.3~75.9 ft-lbs
(87.2~102.9 N.m)

(1) Drive control levers
(2) Adjust bolts
(3) Boots

(1) Drive control lever L.H.

(3) Adjust bolts

(2) Drive control lever R.H.

(4) Adjust plate

ZERO TURN MOWER

1

3

2

1

3

4

2

35 mm (1.38 in)

3

4

FIG. 8-22

FIG. 8-23

«
...
47
48
49
50
51
...
»

Содержание SZ330 SSM60




























































































Отзывы:

Нет отзывов

Похожие инструкции для SZ330 SSM60

Бренд: Baroness Страницы: 85

Бренд: Gardenline Страницы: 20

Бренд: Simplicity Страницы: 32

Бренд: BOXER AGRI Страницы: 15

Бренд: Baroness Страницы: 87

Бренд: Simplicity Страницы: 26

Бренд: Alamo Industrial Страницы: 186

Conquest Garden Tractor & Mower Deck

Бренд: Simplicity Страницы: 48

Бренд: Yard force Страницы: 45

BOB-CAT 942311G

Бренд: Schiller Grounds Care Страницы: 72

Бренд: KUHN Страницы: 48

Бренд: Craftsman Страницы: 56

Бренд: Craftsman Страницы: 56

Бренд: Craftsman Страницы: 56

Бренд: Craftsman Страницы: 60

Бренд: Craftsman Страницы: 60

Бренд: Craftsman Страницы: 60

Бренд: Craftsman Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды