Iseki SZ330 SSM60 Скачать руководство пользователя

Страница: 48 / 91

10. ADJUSTMENT NEUTRAL OF HST CONTROL

LEVER

a. Adjust the HST adjust rod,3, to the neutral position of

the HST pump assy at which the drive control lever,1,
can swing outwards.

b. Please consult your dealer if the neutral position of the

HST pump assy cannot be set properly.

DANGER:Please make sure that the engine is
turned off before adjusting the HST adjust
rod.

11. ADJUSTMENT OF STRAIGHT DRIVE

Please perform the following steps when the zero-turn
mower tends to curve to the left or to the right when both
levers are depressed to their maximum.

a. Remove the boots of the drive control lever at the side

to which the mower tends to curve.

b. Slightly tighten the adjust bolt,1, at the side to which

the mower tends to curve by tightening the lock nut.

c. Start the engine and drive forward to check how much

the zero-turn mower curves.

d. The curvature should be no more than 3 meters after

traveling for 20 meters.

e. When the curvature is within the limit prescribed

above, stop the engine and re-install the boots to its
original position.

DANGER:Please make sure that the engine is
turned off before adjusting the adjust bolt to
adjust straight drive performance.

(1) Drive control lever

(3) HST adjust rod

(2) Rod end

(1) Adjust bolts

CHAPTER 8. MAINTENANCE

FIG. 8-20

FIG. 8-21

Содержание SZ330 SSM60




























































































Результаты поиска

Содержание SZ330 SSM60

Отзывы:

Похожие инструкции для SZ330 SSM60

Бренды по названию

Популярные бренды

Iseki SZ330 SSM60, Руководство по эксплуатации

Результаты поиска

Содержание SZ330 SSM60

Отзывы:

Похожие инструкции для SZ330 SSM60

Бренды по названию

Популярные бренды