Iseki SZ330 SSM60 Скачать руководство пользователя

Страница: 85 / 91

ZERO TURN MOWER

Too low engine output

Gauge wheels do not turn

Blades do not rotate

Mower does not move up or down

Defective hydraulic system.

Height adjust dial is not set in 1.0 inch.

Consult your dealer.

Set it in 1.0 inch.

Loose blade nuts.

Foreign matter caught in blades or blade
supports.

Broken blade pulley.

Broken belt.

Slipping belts.

Broken gears

Re-tighten them.

Clean.

Replace it with a new one.

Adjust belt tension spring
properly.

Consult your dealer.

Foreign matter caught in shaft.

Broken wheel.

Short of grease.

Clean.

Replace it with a new one.

Inject grease.

Too low engine speed.

Too fast travelling speed.

Foreign matter caught between blade and
blade support.

Foreign matter caught in a pulley.

Defective engine.

Mow at full throttle.

Slow down.

Clean.

Consult your dealers.

Troubles

Presumable causes

Remedies

Содержание SZ330 SSM60




























































































Результаты поиска

Содержание SZ330 SSM60

Отзывы:

Похожие инструкции для SZ330 SSM60

Бренды по названию

Популярные бренды

Iseki SZ330 SSM60, Руководство по эксплуатации

Результаты поиска

Содержание SZ330 SSM60

Отзывы:

Похожие инструкции для SZ330 SSM60

Бренды по названию

Популярные бренды