Iseki SZ330 SSM60 Скачать руководство пользователя

Страница: 63 / 91

ZERO TURN MOWER

4. DRIVE CONTROL SYSTEM

5. HST (HYDROSTATIC TRANSMISSION)

Troubles

Presumable causes

Remedies

･

Lift does not rise.

･

Clogged HST oil suction filter

･

Defective hydraulic pump

･

Defective control valve

･

Defective hydraulic cylinder

･

Consult your dealers.

･

Consult your dealers.

･

Consult your dealers.

･

Consult your dealers.

･

Lift does not lower.

･

Defective control valve

･

Height adjust dial is not set in 1.0 inch.

･

Consult your dealers.

･

Set in 1.0 inch.

･

The maximum prescribed

speed is not reached

･

Deterioration in the efficiency of the pump

and motor

･

Faulty setting of the drive control lever linkage

･

Insufficient amount of HST oil

･

Consult your dealer.

･

Adjust the setting by following the

manual instructions.

･

Replenish the HST oil tank with

the prescribed amount of oil.

･

Poor translatory movement

･

Imbalance in efficiencies of the pump and

motor pairs

･

Consult your dealer.

･

Differences in the alignment

of the lever pairs during trans-

latory movement

･

Faulty setting of the control lever linkage

･

Adjust the setting by following the

manual instructions.

･

Zero turn mower does not

start travelling.

･

Parking brake is applied.

･

Too low engine speed

･

Low HST oil tank level

･

Air trapped inside hydraulic piping

･

Improperly adjusted the drive control lever

･

Clogged suction oil filter

･

Defective HST unit

･

Release it.

･

Accelerate engine.

･

Fill to upper limit.

･

Consult your dealers.

･

Consult your dealers.

･

Consult your dealers.

･

Consult your dealers.

･

Zero turn mower creeps

without the drive control

lever being operated

･

Faulty neutral setting of the drive

control lever

･

Incorrect neutral point of HST

･

Improperly positioned neutral arm

･

Defective HST unit

･

Adjust the setting by following the

manual instructions.

･

Consult your dealers.

･

Consult your dealers.

･

Consult your dealers.

Содержание SZ330 SSM60




























































































Результаты поиска

Содержание SZ330 SSM60

Отзывы:

Похожие инструкции для SZ330 SSM60

Бренды по названию

Популярные бренды

Iseki SZ330 SSM60, Руководство по эксплуатации

Результаты поиска

Содержание SZ330 SSM60

Отзывы:

Похожие инструкции для SZ330 SSM60

Бренды по названию

Популярные бренды