Interlogix ATS1500A-IP-LP Скачать руководство пользователя страница 170

Страница: 170 / 376

Chapter 5: Menu reference

164

Advisor Advanced ATSx500A(-IP) Installation and Programming Manual

Note:

This operation is only possible on LCD keypads with integrated readers.

The keypad for card learning is defined in System Options. See “8.8.5 Card

learn-in” on page 255 for more details. If another keypad is defined as a keypad

for card learning, the learning keypad name is prompted, for example:

Badge card
Keypad 3

Removing a card

If the user has a card assigned, you can remove the assigned card. The following

screen appears.

1>Remove card
Card set

Press Enter.

INFO
Card removed

The card has been removed from the selected user.

3.1.n.4 RF fobs

0>Add fob
1 Fob 1

This menu lets you see all fobs programmed for the selected user, select an

existing fob, or create a new one.
The menu contents are similar to the 4 Zones and areas > 4.4 RF fobs menu

described on page 191.

3.1.n.5 Language

5>Language
ENGLISH UK

The Advisor Advanced system can display menus in the preferred language of

each user.
The language is switched after user authorization.
Contact your supplier to get more information about available languages.

3.1.n.6 User groups

1>Not set
2 Not set

Use the User groups menu to assign user groups to the selected user. A user

can have up to 8 user groups assigned. User groups define the options and

areas available for users.
To change a user group assignment, select the appropriate slot.

Содержание ATS1500A-IP-LP

























































































































































































































































































































































































Результаты поиска

Содержание ATS1500A-IP-LP

Отзывы:

Похожие инструкции для ATS1500A-IP-LP

Бренды по названию

Популярные бренды

Interlogix ATS1500A-IP-LP, Инструкция по установке и программированию

Результаты поиска

Содержание ATS1500A-IP-LP

Отзывы:

Похожие инструкции для ATS1500A-IP-LP

Бренды по названию

Популярные бренды