Interlogix ATS1500A-IP-LP Скачать руководство пользователя страница 10

Страница: 10 / 376

Chapter 1: Quick installation and programming

Advisor Advanced ATSx500A(-IP) Installation and Programming Manual

Quick programming

Initial start-up
Note:

See “The Advisor Advanced menu”

on page 106 for menu explanation. For

more information on editing options, see

“How to program the options” on page 108.
Switch the panel on. The further messages

and menus are listed in the table below.

Display

Instructions

INFO
Inst required

Press Enter to continue.

1>Panel language

Choose English.

2>Defaults

Choose EN 50131 Grade 3.

4>PIN length

Enter 6.

5>Time&date

Set current time and date.

6 Install
>Cancel<

Choose OK

Installer
PIN:127800

Press Enter to continue.

Supervisor
PIN:112200

Press Enter to continue.

The panel restarts.

Auto configuration

Auto Config?
>Yes<

Press Enter to continue.

Rkp 1-16 BUS1
R-?-------------
Exp 1-15 BUS1
-?-------------

Wait until the panel

configures all bus devices

and zones.

Added
R:1 D:0 Z:8

Press Enter to continue.

Enabling service in

UTC F&S
THU 05 Mar 12:21

Press 112200, Menu

1>Zone options
2 Isolate

Go to menu 8.8 Service in

8>Service in
Enable?

Enable Installer in time

Press Cancel, Cancel to log off.

Programming menu entry

UTC F&S
THU 05 Mar 12:21

Press 127800, Menu

Inh reports
>No<

Press Enter to continue.

Inh tampers
Unset areas

1>Service menu
2 Device menu

The installer menu is displayed.

Changing installer PIN

Go to 3.1.n.2.1 Change PIN (see page 163).

1>Change PIN
***********

Press Enter.

New PIN
>_

Enter the new installer PIN.

Configuring zones

Go to 4.1 Zone menu (see page 171).

4>Zones&Areas

Press Enter.

1>Zone menu

Press Enter.

0>Add zone
1 Zone 1

Select a zone.

For each zone used in the system, enter

zone name in 4.1.n.1 Zone name (page

172).

01 Zone name
>1 Zone 1 <

Next, set its zone type in 4.1.n.2 Zone type

(see page 172).

Содержание ATS1500A-IP-LP

























































































































































































































































































































































































Результаты поиска

Содержание ATS1500A-IP-LP

Отзывы:

Похожие инструкции для ATS1500A-IP-LP

Бренды по названию

Популярные бренды

Interlogix ATS1500A-IP-LP, Инструкция по установке и программированию

Результаты поиска

Содержание ATS1500A-IP-LP

Отзывы:

Похожие инструкции для ATS1500A-IP-LP

Бренды по названию

Популярные бренды