Interlogix ATS1500A-IP-LP Скачать руководство пользователя страница 149

Страница: 149 / 376

Chapter 5: Menu reference

Advisor Advanced ATSx500A(-IP) Installation and Programming Manual

143

Note:

For expander local devices, select the expander address first, and then

select the local device type.
Press Clear to exit from this view.
Press Enter, then select OK and confirm the new configuration. In this case all

new devices are added, and missing devices are removed from the system.

Note:

The second system bus (BUS2) is only available when using the second

RS485 LAN extension module. See also “Two system databuses” on page 23.

2.2 Edit Keypad&Exp

1>Keypad devices
2 Exp devices

Choose what type of device you want to configure.

2.2.1 Keypad devices

0>Add keypad
1 Keypad 1

Press 0 to add a keypad, or a number to configure an existing one.

Note:

The maximum number of devices allowed on the databus is given in

“General features” on page 36.

Keypad options

2.2.1.0 Add keypad

Keypad number
>_<

On the Add keypad menu, enter the number for this new keypad and press Enter

to confirm or Clear to exit without adding a device.
After the device is added, the keypad configuration options are shown.

2.2.1.n Select keypad

Select the keypad number to configure.

2.2.1.n.1 Keypad type

1>Keypad type
ATS1115

The Keypad type screen is an informational screen. The type is defined by

keypad itself.

Содержание ATS1500A-IP-LP

























































































































































































































































































































































































Результаты поиска

Содержание ATS1500A-IP-LP

Отзывы:

Похожие инструкции для ATS1500A-IP-LP

Бренды по названию

Популярные бренды

Interlogix ATS1500A-IP-LP, Инструкция по установке и программированию

Результаты поиска

Содержание ATS1500A-IP-LP

Отзывы:

Похожие инструкции для ATS1500A-IP-LP

Бренды по названию

Популярные бренды