Interlogix ATS1500A-IP-LP Скачать руководство пользователя страница 148

Страница: 148 / 376

Chapter 5: Menu reference

142

Advisor Advanced ATSx500A(-IP) Installation and Programming Manual

2 Device menu

1>Inst. Remotes
2 Edit Rkp&Exp

Device menu allows you to view and configure bus devices: keypads (RASes),

expanders (DGPs), and readers.
For more information on keypads and expanders, see Chapter 3 “System

functions > Bus devices” on page 58.
For more information on readers, see “Access control” on page 68.
For bus device numbering, see “Bus device numbering” on page 58.

2.1 Installed remotes

1>Keypad devices
2 Exp devices

The Installed remotes menu shows the status of all connected remote keypads

and various system and local expanders.

Note:

The maximum number of devices allowed on the databus is given in

“General features” on page 36.
Select a device type to display.

2.1.1 Keypad devices

2.1.2 Expander devices

Rkp 1-8 BUS1
R-?-----

The bottom line has a list of device states; each device state is shown as one

character, which can be one of the following.
• ?: Device is currently being read

• x: Device is offline or not supported

• I: Device is configured but isolated

• R: Keypad is online and configured (polled)

• r: Keypad is online, but not configured (new)

• D: Expander is online and configured (polled)

• d: Expander is online, but not configured (new)

• M: MI bus expander is online and configured (polled)

• m: MI bus expander is online, but not configured (new)

• c: MI bus expander is online, but its address is in conflict with another

expander

• O: ATS74xx series IP/GPRS dialler is online and configured (polled)

• —: No device

Содержание ATS1500A-IP-LP

























































































































































































































































































































































































Результаты поиска

Содержание ATS1500A-IP-LP

Отзывы:

Похожие инструкции для ATS1500A-IP-LP

Бренды по названию

Популярные бренды

Interlogix ATS1500A-IP-LP, Инструкция по установке и программированию

Результаты поиска

Содержание ATS1500A-IP-LP

Отзывы:

Похожие инструкции для ATS1500A-IP-LP

Бренды по названию

Популярные бренды