Interlogix ATS1500A-IP-LP Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 376

background image

Chapter 2: Installation

40

Advisor Advanced ATSx500A(-IP) Installation and Programming Manual

Example for ATS3500A(-IP) EN Grade 3

When using battery backup as specified for EN Grade 3 using an 18 Ah battery,

the maximum available auxiliary current is 450 mA.
This current is the max grand total available current that may be used for

auxiliary components such as:
• Devices on the Advisor Advanced system databus

• Detectors on the auxiliary power output

• Communication devices via MI-bus (e.g. GSM, IP)
Temporary used current such as: Sirens and Strobes are not included.
Fuse rating must be taken into account.

Battery status information

Various detection ways are provided to understand the status of a battery.
A short battery test will be applied to detect following within 10 seconds:
• Battery fail (or battery missing) to inform installer no battery is attached or a

poor battery is attached. Event will be logged and notified.

• Low battery as soon as battery becomes below 10.5 V with or without mains.

Event will be logged, notified and reported.

Another battery test will be applied once per day to even better understand

battery status. In case battery wears out a battery fail message will be logged,

notified and reported.

System monitoring

The system provides monitoring for the following items.

Table 10: Monitored items
Monitoring function Message

Cause

AC Mains

Mains fail

Loss of external power supply [1]

Battery

Battery low

Battery low voltage [1]

Battery test fail

Exhausted battery
Battery charger fail

Fuse/power output fail

Output overload

Power outputs

Fuse/power output fail

Exhausted fuse
Fuse loss
Short circuit
Overload

Power supply

Power unit/power output fail Power unit failure

Overvoltage

Tampers

Device tamper

Device sabotage

[1] Mains fail and Battery low will finally result in Battery deep discharge protection.

«
...
44
45
46
47
48
...
»

Содержание ATS1500A-IP-LP

























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ATS1500A-IP-LP

Бренд: K&K Страницы: 6

Бренд: Gardena Страницы: 18

VLT Micro Drive FC 51 Series

Бренд: Danfoss Страницы: 23

Бренд: Danfoss Страницы: 37

Бренд: Daikin Страницы: 44

Бренд: ICP DAS USA Страницы: 166

Бренд: ICP DAS USA Страницы: 64

Tunnel Master Jr

Бренд: ICS Страницы: 83

PROFIBUS PROFI-2510

Бренд: ICP DAS USA Страницы: 4

Бренд: ICP DAS USA Страницы: 40

Бренд: Jabra Страницы: 3

Бренд: B&G Страницы: 19

Бренд: KIPI Страницы: 44

Бренд: Gallagher Страницы: 2

Бренд: Case IH Страницы: 81

Бренд: Belimo Страницы: 2

Бренд: Watts Страницы: 12

MultiConnect Dragonfly MTQ-MNA1-B01

Бренд: Multitech Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды