Interlogix ATS1500A-IP-LP Скачать руководство пользователя страница 279

Страница: 279 / 376

Chapter 5: Menu reference

Advisor Advanced ATSx500A(-IP) Installation and Programming Manual

273

9.3.n.7.1 Firewall

1 Firewall
>On<

Use the Firewall menu to enable (On) or disable (Off) the built-in firewall.

9.3.n.7.2 Reply on PING

2 Reply on PING
>No<

The Reply on PING defines whether the firewall allows answering to ping

requests. If this option is set to No, ping requests are not answered.

9.3.n.8 Link speed

8 Link speed
>10 MB<

The Link speed menu allows you to choose the Ethernet link speed. The allowed

options are:
• 10 MB

• 100 NB

• Auto

9.3.n.9 MAC address

9>MAC address
0051DB3D7E73

MAC address of the Ethernet controller is a read-only value.

9.3.n.10 Max Pics 24h

10 Max Pics 24h
> <

You can limit the maximum number of pictures sent to users via GPRS or IP

transmission path during a 24-hour period.
If the limit is reached, further picture requests are denied by the system and an

appropriate event is recorded in the log.
There is no limit for pictures if this value is set to 0.

GSM/SMS/GPRS specific options

9.3.n.4 Transm path

4 Transm path
ETHERNET

The Transmission path option is a read-only field that identifies a communication

method used for this transmission path.

Содержание ATS1500A-IP-LP

























































































































































































































































































































































































Результаты поиска

Содержание ATS1500A-IP-LP

Отзывы:

Похожие инструкции для ATS1500A-IP-LP

Бренды по названию

Популярные бренды

Interlogix ATS1500A-IP-LP, Инструкция по установке и программированию

Результаты поиска

Содержание ATS1500A-IP-LP

Отзывы:

Похожие инструкции для ATS1500A-IP-LP

Бренды по названию

Популярные бренды