Interlogix ATS1500A-IP-LP Скачать руководство пользователя страница 175

Страница: 175 / 376

Chapter 5: Menu reference

Advisor Advanced ATSx500A(-IP) Installation and Programming Manual

169

3.2.n.3 User group areas

01-10>UG areas
1.........

The User group areas option defines which areas the user can control.

3.2.n.4 User group AG

01-10>UG AG
1.........

The UG area group option defines which area groups the user can control.

3.2.n.5 User group filter

5>UG filter
Not used

When using a filter, the user rights defined by the user group depend on this filter

state.
For more information on condition filters, see “6.1 Condition filters” on page 217.

3.2.n.6 User group options

6>UG options
>>>

User group options define the user access rights to the particular options.
Available options are listed in “User group options” on page 64.

3.2.n.7 Schedule

Select schedules for the selected user group.
The shortcut menu allows you to assign up to two schedules to each of the

following elements:
• 1 Privileges
• 2 Area access

See “Schedule shortcut menu” on page 78 for more information.

3.2.n.8 Remove user group

To remove a user group, select a user group using the cursor, or by entering the

user group number, and go to the Delete UG menu.
The display shows:

8 Remove UG
>Cancel<

Choose Ok and press Enter. This removes the user group.
Repeat the command to delete other user groups, or press Clear to exit and

return to the higher menu level.

Содержание ATS1500A-IP-LP

























































































































































































































































































































































































Результаты поиска

Содержание ATS1500A-IP-LP

Отзывы:

Похожие инструкции для ATS1500A-IP-LP

Бренды по названию

Популярные бренды

Interlogix ATS1500A-IP-LP, Инструкция по установке и программированию

Результаты поиска

Содержание ATS1500A-IP-LP

Отзывы:

Похожие инструкции для ATS1500A-IP-LP

Бренды по названию

Популярные бренды