Interlogix ATS1500A-IP-LP Скачать руководство пользователя страница 309

Страница: 309 / 376

Chapter 8: Regulations

Advisor Advanced ATSx500A(-IP) Installation and Programming Manual

303

Refer to appropriate sections and manuals.

Caution:

When any option, any additional function or any additional zone type in

this section does not comply with the EN 50131 requirements, the EN 50131

Grade 2 label must be removed from the system.

Additional functions

The Wireless PIR Camera functionality brings along video verification feature,

this additional function is fully available without compromise to standards the

system complies to.
The Wireless PIR camera system consists of the following:
• Advisor Advanced series control panel

• ATS1238 Advanced Wireless DGP

• TX-2344-03-1 Wireless PIR Camera

• ATS7310 GSM/GPRS Module
These PIR camera settings have no influence on EN 50131 compliance:
• 2.2.2.n.4.9.1.1.2 Frame rate for all event types

• 2.2.2.n.4.9.1.1.3 Pic resolution for all event types

• 2.2.2.n.4.9.3 Pic auto deletion

• 4.5 Cameras

• 9.1.n.4.5 Vid dest port

• 9.3.n.10 Max Pics 24h, 9.3.n.7.9 Max Pics 24h

EN 50131 Grade 3

Required settings

The following options and values are mandatory for EN 50131-1 Grade 3

regulations:
• All Grade 2 required settings (see “EN 50131 Grade 2” on page 302).

• PIN length should be 6 digits minimum. See also “8.7.4 PIN length”.

• 3.2.n.6 User group options, set (6) Isolate, (22) SMS reporting, (23) SMS

control to No for all user groups except Installer.

• 4.1.n.6.7 Anti mask, set to Yes for all I&HAS movement detectors

• 8.1.3.1 Armed display, set to 00’00

• 8.3.5 View EE timer, set to Off

• 8.4.1 RTS options, set Zone masking condition to Yes

• 8.4.2 Inhibit includes, set Zone masking condition to Access Level 2

• Battery test should be performed daily. See “1.2.9 Battery test” on page 135

for details.

The following features are not allowed (not evaluated):
• Keyswitch zone types to set and unset the system. See “Zone types” on page

45.

• Presetting indication and any automatic override of set prevention.

Содержание ATS1500A-IP-LP

























































































































































































































































































































































































Результаты поиска

Содержание ATS1500A-IP-LP

Отзывы:

Похожие инструкции для ATS1500A-IP-LP

Бренды по названию

Популярные бренды

Interlogix ATS1500A-IP-LP, Инструкция по установке и программированию

Результаты поиска

Содержание ATS1500A-IP-LP

Отзывы:

Похожие инструкции для ATS1500A-IP-LP

Бренды по названию

Популярные бренды