Interlogix ATS1500A-IP-LP Скачать руководство пользователя страница 215 | Manualshive

Страница: 215 / 376

background image

Chapter 5: Menu reference

Advisor Advanced ATSx500A(-IP) Installation and Programming Manual

209

5.1.n.6.4.2 RTE zone

0>Not used
19 Zone 19

Select a zone operating as an RTE input for an intelligent door.

Note:

It is not possible to choose a zone, which is already used in the door

controller (for example, DOTL or door zone, etc.)
See also “5.1.n.6.4 RTE options” on page 201.

5.1.n.6.4.3 Dis. when set

1>IN reader
2 OUT reader

Specify if the RTE functionality is disabled if any of door areas are set.
First, select the appropriate IN or OUT reader. Next, set Yes or No to configure

the option for the specified reader.

5.1.n.6.4.4 RTE Control

4 RTE Control
>Timed door OP<

Defines the operation of the Request To Exit button.
• Timed door open. When the RTE button is pressed, the door unlocks for the

programmed unlock time. See “5.1.n.5.1 Unlock time” on page 198.

• Hold door open. Allows the door to be held unlocked for as long as the RTE

button is pressed or for the programmed unlock time, whichever is longer.

• Shunt only. When the RTE button is pressed, the zone is shunted, but no

access is granted.

5.1.n.6.5 Reporting

1>CL & Locked
No

Determines when access control events are reported.

5.1.n.6.5.1 CL & Locked

1 CL & Locked
>No<

If set to yes, the door is reported when closed and locked (lock command sent,

and zone status is normal).

Note:

There is no event specified in the control panel. This function can only be

used in conjunction with next options.

«
...
213
214
215
216
217
...
»

Содержание ATS1500A-IP-LP

























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ATS1500A-IP-LP

Бренд: Lawler Страницы: 4

Бренд: Hama Страницы: 46

Бренд: Galcon Страницы: 35

Бренд: Easy-Laser Страницы: 84

Бренд: Easy Heat Страницы: 4

Бренд: J3C Страницы: 2

Бренд: IDS Страницы: 2

Бренд: Atari Страницы: 3

Бренд: Konig Страницы: 47

MultiConnect Dragonfly MTQ-MNA1-B01

Бренд: Multitech Страницы: 45

Бренд: GEM Страницы: 31

Бренд: FADAL Страницы: 2

Бренд: Zander Aachen Страницы: 75

Бренд: DAPAudio Страницы: 11

Бренд: Akytec Страницы: 15

Бренд: PI Страницы: 6

Бренд: Avanza Страницы: 10

Бренд: VOSS Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды