Interlogix ATS1500A-IP-LP Скачать руководство пользователя страница 169

Страница: 169 / 376

Chapter 5: Menu reference

Advisor Advanced ATSx500A(-IP) Installation and Programming Manual

163

3.1.n.2.1 Change PIN

1 PIN
***********

Change the selected user PIN.
See “PIN” on page 66 for details on PIN usage.

3.1.n.2.2 Remote PIN

1>Set PIN
***********

Remote PIN is a PIN for programming the panel via remote connection. If remote

PIN is not set, the installer uses local PIN to log in remotely.

Note:

This submenu is available for installer only. If the option “8.7.8.2 Remote

PIN” on page 253 allows it, the submenu is also available for the supervisor.
See “Remote access” on page 113 for more details.

3.1.n.2.2.1 Set PIN

1>Set PIN
> <

Set remote PIN.
To enable remote PIN, use “3.1.n.2.2.2 Enable login” below.

3.1.n.2.2.2 Enable login

2>Enable login
>Yes<

Use the command to enable remote PIN.
See “3.1.n.2.2 Remote PIN” above for more details.

3.1.n.3 User card

1>Assign card
Card not set

The User card menu lets you assign or delete a user card.
The content of the menu depends whether a card has been already assigned or

not.

3.1.n.3.1 Assign card

If the user has no card assigned, the menu lets you enter a user card number.
Press Enter and present the card at the keypad within 10 seconds.

INFO
Badge card

Содержание ATS1500A-IP-LP

























































































































































































































































































































































































Результаты поиска

Содержание ATS1500A-IP-LP

Отзывы:

Похожие инструкции для ATS1500A-IP-LP

Бренды по названию

Популярные бренды

Interlogix ATS1500A-IP-LP, Инструкция по установке и программированию

Результаты поиска

Содержание ATS1500A-IP-LP

Отзывы:

Похожие инструкции для ATS1500A-IP-LP

Бренды по названию

Популярные бренды