Interlogix ATS1500A-IP-LP Скачать руководство пользователя страница 112

Страница: 112 / 376

Chapter 4: Programming

106

Advisor Advanced ATSx500A(-IP) Installation and Programming Manual

The Advisor Advanced menu

If you attempt to select an option that is not authorized for your PIN (for example,

user menus), the display shows the message:

ERROR
Access denied

Note:

When an incorrect PIN is entered three times the keypad is locked for 120

seconds.

User code requirement

The system can be configured to prevent the installer from accessing the menus

without permission from the manager. This is required, for example, by EN 50131

regulations. This is set in the menu “8.2.1 User code required” (see page 237).

Challenge code requirement

The system can be configured to prevent the installer from accessing the menus

without permission from the central station operator. In this case the installer gets

a 10-digit request code displayed on LCD when entering the menu. He must call

the central station and provide this request code to the operator. Next, the central

station operator generates a unique challenge code and provides it to the

installer. The installer then uses this challenge code to access the programming

menus.
This code is valid during the time period set in “8.1.3.6 Installer in-time” on page

235.
The option is enabled in “8.2.6 Challenge code” on page 240.

How the menu sections are organized in this manual

The menu entries are numbered in the Advisor Advanced system. This

numbering system is also used in this manual, so menu option 1 “Inhibit zones” is

described in section “1 Inhibit zones”.
The menu number also refers to the key sequence you press to enter it. For

example, if you want to enter menu 1.4 Walk test, you can press 1, 4 after

entering the installer menu.

Содержание ATS1500A-IP-LP

























































































































































































































































































































































































Результаты поиска

Содержание ATS1500A-IP-LP

Отзывы:

Interlogix ATS1500A-IP-LP, Инструкция по установке и программированию, Страница: 112 / 376

Результаты поиска

Содержание ATS1500A-IP-LP

Отзывы: