Interlogix ATS1500A-IP-LP Скачать руководство пользователя страница 261

Страница: 261 / 376

Chapter 5: Menu reference

Advisor Advanced ATSx500A(-IP) Installation and Programming Manual

255

8.8.3 System tamper areas

3 SysTamp areas
>1.......<

The System tamper areas option allows assigning system tampers and faults to

the specified areas. At least one area must be selected.

8.8.4 Siren retrigger

4 Siren retrig.
>No<

If there are multiple alarms, and the Siren retrigger option is set to Yes, the

external siren activates every time an alarm occurs. Otherwise, the external siren

activates only after the first alarm.

8.8.5 Card learn-in

5 Card learn-in
>Keypad 1<

Choose a keypad for user card learning. See also “3.1.n.3 User card” on page

163.

8.8.6 Test inputs

6 Test inputs
>All<

The Test inputs option defines what inputs should be accessible when

performing input tests as described in “1.2.1 Input tests” on page 121. The

following options are available:
• All: All inputs are visible.
• If used: Only the inputs assigned to the existing zones are visible.

8.8.7 Buzzer mode

7 Buzzer mode
>Continuous<

The Buzzer mode menu defines how the keypad buzzer works during the exit

time. The following options are available:
• Continuous: The keypad buzzer emits a continuous sound that switches to an

intermittent during an entry/exit or access zone activity.

• Intermittent: The keypad buzzer emits a continuous sound and switches to an

intermittent 10 seconds before the exit time expires.

Содержание ATS1500A-IP-LP

























































































































































































































































































































































































Результаты поиска

Содержание ATS1500A-IP-LP

Отзывы:

Похожие инструкции для ATS1500A-IP-LP

Бренды по названию

Популярные бренды

Interlogix ATS1500A-IP-LP, Инструкция по установке и программированию

Результаты поиска

Содержание ATS1500A-IP-LP

Отзывы:

Похожие инструкции для ATS1500A-IP-LP

Бренды по названию

Популярные бренды