Intel R2600SR Series Скачать руководство пользователя страница 70

Страница: 70 / 85

Intel® Server System R2600SR Setup and Service Guide

Note: Make sure the pins on the system shuttle are fully seated in the system chassis slots.

Push the handles down and turn the thumbscrews clockwise (see Number 1).

If the cable management arm was removed, re-install it.

Reconnect the power cords and any cables that were removed.

Push all compute nodes back into the enclosure (see Section 3.2.2).

3.16

Replacing the PCIe* Add-in Card

The add-in cards in the system are installed in a PCIe* cassette in the rear of the system. In order to replace
an add-in card, the PCIe cassette assembly must be removed and disassembled. The PCIe cassette is reused
to install the new add-in card.

3.16.1

Preparing to Remove a PCIe* Add-in Card

Before removing a PCIe* Add-in Card, perform the following procedure:

Turn off the compute node to which the add-in card is connected.

Locate the add-in card on the rear side of the system.

Disconnect any cables attached to the add-in card.

Figure 56. PCIe* Add-in Card location, system rear

Содержание R2600SR Series






















































































Результаты поиска

Содержание R2600SR Series

Отзывы:

Похожие инструкции для R2600SR Series

Бренды по названию

Популярные бренды

Intel R2600SR Series, Руководство по установке и обслуживанию

Результаты поиска

Содержание R2600SR Series

Отзывы:

Похожие инструкции для R2600SR Series

Бренды по названию

Популярные бренды