Intel R2600SR Series Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 85

background image

Intel® Server System R2600SR Setup and Service Guide

8

Replacing the DIMMs Section 3.6 Instructions for replacing the Dual Inline Memory Module (DIMM).
Replacing the Drive Carrier Section 3.7 Instructions for replacing the Drive Carrier.

Replacing the Drive Backplane   Section 3.8  Instructions for replacing the Drive Backplane.
Replacing the KVM Module   Section 3.9  Instructions for replacing the KVM Module.
Replacing the Server Board   Section 3.10 Instructions for replacing the Server Board.
Updating Configuration After System Update   Section 3.11  Instructions for replacing the
Configuration.
Replacing System Fans   Section 3.12 Instructions for replacing the System Fans.
Replacing the Power Supply Unit (PSU)   Section 3.13  Instructions for replacing the PSU.
Replacing the System Management Module (SMM)   Section 3.14  Instructions for replacing the SMM.

Replacing the External I/O Module (EIOM) Section 3.15 Instructions for replacing the EIOM.
Replacing the PCIe* Add-in Card Section 3.16 Instructions for replacing the PCIe* Add-in Card.

Getting Help Appendix A
Glossary Appendix B

1.4

Resource Information and Software

For additional information about the Intel

®

Server System R2600SR product family products or any of their

supported accessories, refer to the following resources available at:

http://www.intel.com/support

Table 1. Server system references

For this Information or Software

Use this Document or Software

In-depth technical information about
this product family



Intel

®

Server System R2600SR Product Family Technical Product Specification



Intel® Server System BIOS Setup Utility Guide



Product Safety and Regulatory Compliance - Intel® Xeon® processor Scalable
Family

System integration instructions and
service guidance



Intel® Server System R2600SR Product Family Setup and Service Guide

Server configuration guidance and
compatibility



Intel® S2600SR Product Family Configuration Guide

System firmware updates, onboard
device drivers, and software to manage
the Intel

®

Server System

http://downloadcenter.intel.com/

The server system has support for software utilities which can be used to configure system parameters and
aid in troubleshooting system issues. Download all available utilities from:

http://downloadcenter.intel.com/

«
...
12
13
14
15
16
...
»

Содержание R2600SR Series






















































































Отзывы:

Нет отзывов

Похожие инструкции для R2600SR Series

Бренд: HYVE Страницы: 22

Бренд: Premio Страницы: 3

e Server iSeries 825

Бренд: IBM Страницы: 52

Бренд: i3 International Страницы: 2

SUPERSERVER 5018A-MHN4

Бренд: Supermicro Страницы: 116

RS/6000 7043 260

Бренд: IBM Страницы: 322

Бренд: BELINEA Страницы: 53

Бренд: Velvac Страницы: 55

Бренд: W&T Страницы: 228

Бренд: Cisco Страницы: 2

Бренд: Artesyn Embedded Technology Страницы: 2

Бренд: Amulet Hotkey Страницы: 2

Бренд: San Telequip Страницы: 26

Бренд: Eelectron Страницы: 42

Бренд: Eelectron Страницы: 113

STRATOS S910 Series

Бренд: QCT Страницы: 41

Бренд: Tektronix Страницы: 50

Бренд: TAG Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды