Intel R2600SR Series Скачать руководство пользователя страница 30

Страница: 30 / 85

Intel® Server System R2600SR Setup and Service Guide

Remove the compute node from the system. (see Section 0)

Push the cover release latch on the top of the node cover.

Slide the cover toward the rear of the node until the cover has disengaged from the node, then lift the
cover up and away from the node.

3.1.4

Installing the Compute Node Cover

Once repair or upgrade work is completed on the inside of the compute node, re-install the compute node
cover. To re-install the compute node cover, follow these steps:

Figure 15. Installing the compute node cover

Make sure that all internal cables are correctly routed.

Align the cover pins with the notches in the node side walls, then lower the cover on top of the node.

Slide the cover forward towards the front of the node until the cover latches in place.

Note: Before sliding the cover forward, make sure that all the tabs on the front, rear, and side of the cover
engage the side walls correctly.

Содержание R2600SR Series






















































































Результаты поиска

Содержание R2600SR Series

Отзывы:

Похожие инструкции для R2600SR Series

Бренды по названию

Популярные бренды

Intel R2600SR Series, Руководство по установке и обслуживанию

Результаты поиска

Содержание R2600SR Series

Отзывы:

Похожие инструкции для R2600SR Series

Бренды по названию

Популярные бренды