Intel R2600SR Series Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 85

background image

Intel® Server System R2600SR Setup and Service Guide

23

3.1.2

Installing the Compute Node

Figure 13. Installing the compute node

1.

Make sure that the locking lever on the compute node is turned all the way left.

2.

Slide the compute node into the node bay until it stops.

3.

Secure the compute node by turning the locking lever all the way to the right until it clicks into place.

4.

Check the power LED to ensure it transitions between fast blink and slow blink to indicate the node is
ready to be powered on.

The time required for a compute node to initialize varies by system configuration. The power LED flashes
rapidly during initialization; the power button on the compute node does not respond until the power LED
flashes slowly, indicating the initialization process is complete.

Note: If the node configuration has been changed or a different configuration is being installed, configure the
compute node through the <F1> BIOS Setup utility.

3.1.3

Removing the Compute Node Cover

Before removing the compute node cover, perform these steps:

Figure 14. Removing the compute node cover

«
...
27
28
29
30
31
...
»

Содержание R2600SR Series






















































































Отзывы:

Нет отзывов

Похожие инструкции для R2600SR Series

Бренд: IBM Страницы: 180

8841 - eServer xSeries 236

Бренд: IBM Страницы: 100

Бренд: Hawking Страницы: 40

Бренд: TYAN Страницы: 106

Бренд: Brother Страницы: 103

Бренд: GRASS VALLEY Страницы: 2

Бренд: ORing Industrial Networking Corp. Страницы: 2

ZXCLOUD iBox CT220

Бренд: Zte Страницы: 16

Proline Promass 300 EtherNet/IP

Бренд: TechnipFMC Страницы: 36

Бренд: Silicon Graphics Страницы: 66

Бренд: Tektronix Страницы: 50

Бренд: Vlinx Страницы: 47

21000 Appliances G-70

Бренд: Check Point Страницы: 3

Бренд: IBM Страницы: 136

Бренд: 3Com Страницы: 122

QuantaGrid Q71L-4U

Бренд: QUANTA Страницы: 24

UniServer B5700 G5

Бренд: H3C Страницы: 90

ixia Application Server

Бренд: Keysight Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды