Intel R2600SR Series Скачать руководство пользователя страница 60

Страница: 60 / 85

Intel® Server System R2600SR Setup and Service Guide

3.12.3

Installing a System Fan

Install a 60x60x56mm fan by completing the following steps.

Figure 43.

Installing the 60x60x56mm fan

Ensure the airflow arrow on the fan label on the top of the fan is pointed towards the rear of the system.

Position the fan over the socket to receive the fan and lower the fan into the socket.

Push the fan assembly downward until the locking tab clicks into place.

Install an 80x80x80mm fan by completing the following steps.

Figure 44.

Installing a 80x80x80mm fan

Ensure the airflow arrow on the fan label on the top of the fan is pointed towards the rear of the system.
Position the fan over the socket to receive the fan and lower the fan into the socket.

Lower the fan into the socket, and push it downward until it clicks into place (see Letter A).

Connect the power cable by pushing the connector into the socket until the locking tab clicks (see
Letter B).

Carefully route the cable underneath the flange and make sure the cable is routed through the notch
in the circuit board (see Letter C).

Содержание R2600SR Series






















































































Результаты поиска

Содержание R2600SR Series

Отзывы:

Похожие инструкции для R2600SR Series

Бренды по названию

Популярные бренды

Intel R2600SR Series, Руководство по установке и обслуживанию

Результаты поиска

Содержание R2600SR Series

Отзывы:

Похожие инструкции для R2600SR Series

Бренды по названию

Популярные бренды