Intel R2600SR Series Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 85

background image

Intel® Server System R2600SR Setup and Service Guide

20

2.4

System Firmware Update and Backup

The system includes a software stack to operate which includes a BIOS, BMC firmware, ME firmware, and FRU
and SDR data. A default software stack is loaded during the system manufacturing process; however, it may
not be the latest available. For best operation and system reliability, it is highly recommended that the
software stack be updated to the latest available version.

The latest version of the system software stack can be downloaded at:

http://downloadcenter.intel.com

For information and action steps, please see the Intel® Server System R2600SR Product Family System
Management Module User's Guide.

2.4.1

Backing Up the System Configuration

After setting up the system or making changes to the configuration, it is recommended to make a complete
backup of the system configuration.
For detailed information and procedures, please see the Intel® Server System R2600SR Product Family
System Management Module User's Guide.

«
...
24
25
26
27
28
...
»

Содержание R2600SR Series






















































































Отзывы:

Нет отзывов

Похожие инструкции для R2600SR Series

Бренд: Xerox Страницы: 2

Бренд: Xerox Страницы: 2

Бренд: YOKOGAWA Страницы: 22

Enterprise Server

Бренд: Blackberry Страницы: 88

Бренд: Sercomm Страницы: 75

Silex Pricom SX-2000U2

Бренд: Silex technology Страницы: 1

Бренд: RackSolutions Страницы: 8

@server x Series

Бренд: IBM Страницы: 8

Titan SiliconServer

Бренд: Blue Arc Страницы: 487

Бренд: Atrust Страницы: 21

Бренд: ATON Страницы: 2

ABLELink SW2001

Бренд: Atop Страницы: 51

ABLELink GW21 MAXI Series

Бренд: Atop Страницы: 110

Бренд: ClearCube Страницы: 3

G4-Apex-ENTERPRISE-HW

Бренд: Viavi Страницы: 8

DeviceMaster PRO

Бренд: Comtrol Страницы: 174

Бренд: QSSC Страницы: 98

Бренд: QSSC Страницы: 99

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды