Intel Pentium II Скачать руководство пользователя страница 98 | Manualshive

Страница: 98 / 226

Intel Pentium II Скачать руководство пользователя страница 98

ELECTRICAL SPECIFICATIONS

E

7-22

8/29/97 11:14 AM CH07.DOC

INTEL CONFIDENTIAL

(until publication date)

Table 7-12. Pentium

®

II Processor System Bus AC Specifications

(CMOS Signal Group)

(1, 2, 3)

T#

Parameter

Min

Max

Unit

Figure

Notes

T11:

2.5 Output Valid Delay

1.00

10.5

ns

7-7

4

T12:

2.5 Input Setup Time

5.50

ns

7-8

5, 6

T13:

2.5 Input Hold Time

1.75

ns

7-8

5

T14:

2.5 Input Pulse Width, except
PWRGOOD

2

BCLKs

7-7

Active and Inactive
states

T15:

PWRGOOD Inactive Pulse
Width

10

BCLKs

7-7

7-11

7

NOTES:

1.

Not 100% tested. Specified by design characterization.

2.

All AC timings for the CMOS signals are referenced to the BCLK rising edge at 0.7V at the processor
edge fingers. All CMOS signal timings are referenced at 1.25V at the processor edge fingers.

3.

These signals may be driven asynchronously, but must be driven synchronously in FRC model.

4.

Valid delay timings for these signals are specified to 2.5V +5%. See Table 7-3 for pull-up resistor values.

5.

To ensure recognition on a specific clock, the setup and hold times with respect to BCLK must be met.

6.

INTR and NMI are only valid during APIC disable mode. LINT[1:0] are only valid during APIC enabled
mode.

7.

When driven inactive or after Vcc

CORE

, Vcc

L2

and BCLK become stable.

Table 7-13. System Bus AC Specifications (Reset Conditions)

T#

Parameter

Min

Max

Unit

Figure

Notes

T16:

Reset Configuration Signals
(A[14:5]#, BR0#, FLUSH#,
INIT#) Setup Time

4

BCLKs

7-10

Before deassertion of
RESET

T17:

Reset Configuration Signals
(A[14:5]#, BR0#, FLUSH#,
INIT#) Hold Time

2

20

BCLKs

7-10

After clock that
deasserts RESET#

T18:

Reset Configuration Signals
(A20M#, IGNNE#, LINT[1:0])
Setup Time

1

ms

7-10

Before deassertion of
RESET#

T19:

Reset Configuration Signals
(A20M#, IGNNE#, LINT[1:0])
Delay Time

5

BCLKs

7-10

After assertion of
RESET#

(1)

T20:

Reset Configuration Signals
(A20M#, IGNNE#, LINT[1:0])
Hold Time

2

20

BCLKs

7-10
7-11

After clock that
deasserts RESET#

NOTE:

1.

For a Reset, the clock ratio defined by these signals must be a safe value (their final or lower multiplier)
within this delay unless PWRGOOD is being driven inactive.

«
...
96
97
98
99
100
...
»

Содержание Pentium II



































































































































































































































Отзывы:

Нет отзывов