Intel Ethernet 10G 2P X520 Adapter Скачать руководство пользователя страница 139 | Manualshive

Страница: 139 / 153

background image

EMC Compliance

l

FCC Part 15 - Radiated & Conducted Emissions (USA)

l

ICES-003 - Radiated & Conducted Emissions (Canada)

l

CISPR 22 - Radiated & Conducted Emissions (International)

l

EN55022:2006 - Radiated & Conducted Emissions (European Union)

l

EN55024:1998 +A1:2001 +A2:2003 - Immunity (European Union)

l

EU - EMC Directive 2004/108/EC

l

VCCI - Radiated & Conducted Emissions (Japan)

l

CNS13438-2006 - Radiated & Conducted Emissions (Taiwan)

l

AS/NZS CISPR 22 - Radiated & Conducted Emissions (Australia/New Zealand)

l

KCC notice 1997-41 - EMI and KCC notice 1997-42 - EMS (Korea)

Regulatory Compliance Markings

When required these products are provided with the following Product Certification Markings:

l

UL Recognition Mark for USA and Canada

l

CE Mark

l

FCC markings

l

VCCI marking

l

Australian C-Tick Mark

l

Korea KCC mark

l

Taiwan BSMI mark

l

People's Republic of China "EFUP" mark

Class B Products

FCC Class B User Information

This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of
the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guar-
antee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following meas-
ures:

l

Reorient or relocate the receiving antenna.

l

Increase the separation between the equipment and receiver.

l

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

l

Consult the dealer or an experienced radio/TV technician for help.

CAUTION: If the device is changed or modified without permission from Intel, the user may void his or
her authority to operate the equipment.

NOTE:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

Class 1 Laser Products

These server adapters contain laser devices for communication use. These devices are compliant with the require-
ments for Class 1 Laser Products and are safe in the intended use. In normal operation the output of these laser
devices does not exceed the exposure limit of the eye and cannot cause harm.

«
...
137
138
139
140
141
...
»

Содержание Ethernet 10G 2P X520 Adapter


























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ethernet 10G 2P X520 Adapter

Бренд: j5 create Страницы: 444

Бренд: Teufel Страницы: 24

Бренд: Otto Bock Страницы: 160

Бренд: KTI Страницы: 25

Бренд: Gossen MetraWatt Страницы: 2

Бренд: Allied Telesis Страницы: 2

WAB501 - 802.11a/b Dual Band PC Card

Бренд: NETGEAR Страницы: 17

Бренд: Lindy Страницы: 16

HHM Series HHM2208SB1

Бренд: TDK Страницы: 2

Бренд: Yealink Страницы: 32

Бренд: Somogyi Elektronic Страницы: 2

VELOCITY NP900n

Бренд: NetComm Страницы: 6

POWERLINE NP504

Бренд: NetComm Страницы: 6

Бренд: NetComm Страницы: 2

Бренд: NetComm Страницы: 2

Бренд: Crown Страницы: 2

Бренд: SOHARD Страницы: 35

Бренд: HQ Power Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды