Intel Ethernet 10G 2P X520 Adapter Скачать руководство пользователя страница 21

Страница: 21 / 153

Using the Adapter

Testing the Adapter

Intel's diagnostic software lets you test the adapter to see if there are problems with the adapter hardware, the cabling,
or the network connection.

Tests for Windows

Intel PROSet allows you to run four types of diagnostic tests.

Connection Test: Verifies network connectivity by pinging the DHCP server, WINS server, and gateway.

Cable Tests: Provide information about cable properties.

NOTE:

The Cable Test is not supported on:

Intel® Ethernet Server Adapter X520-2

Intel® Ethernet X520 10GbE Dual Port KX4
Mezz

Intel® Ethernet X520 10GbE Dual Port KX4-
KR Mezz

Intel® Ethernet 10G 2P X520 Adapter

Intel® Ethernet 10G 2P X520-k bNDC

Intel® Ethernet 10G 4P X520/I350 rNDC

Intel® Ethernet 10G 2P X540-t Adapter

Intel® Ethernet 10G 4P X540/I350 rNDC

Intel® Gigabit 4P I350-t Mezz

Intel® Gigabit 4P X520/I350 rNDC

Intel® Ethernet Connection I354 1.0 GbE
Backplane

Intel® Gigabit 4P I350 bNDC

Intel® Gigabit 2P I350 LOM

Hardware Tests: Determines if the adapter is functioning properly.

NOTE:

Hardware tests will fail if the adapter is configured for iSCSI Boot.

To access these tests, select the adapter in Windows Device Manager, click the

Link

tab, and click

Diagnostics

. A Dia-

gnostics window displays tabs for each type of test. Click the appropriate tab and run the test.

The availability of these tests is hardware and operating system dependent.

DOS Diagnostics

Use the

DIAGS

test utility to test adapters under DOS.

Linux Diagnostics

The driver utilizes the ethtool interface for driver configuration and diagnostics, as well as displaying statistical inform-
ation. ethtool version 1.6 or later is required for this functionality.

The latest release of ethtool can be found at:

http://sourceforge.net/projects/gkernel

NOTE:

ethtool 1.6 only supports a limited set of ethtool options. Support for a more complete ethtool feature set

can be enabled by upgrading ethtool to the latest version.

Содержание Ethernet 10G 2P X520 Adapter


























































































































































Результаты поиска

Содержание Ethernet 10G 2P X520 Adapter

Отзывы:

Похожие инструкции для Ethernet 10G 2P X520 Adapter

Бренды по названию

Популярные бренды

Intel Ethernet 10G 2P X520 Adapter, Руководство пользователя

Результаты поиска

Содержание Ethernet 10G 2P X520 Adapter

Отзывы:

Похожие инструкции для Ethernet 10G 2P X520 Adapter

Бренды по названию

Популярные бренды