Intel Ethernet 10G 2P X520 Adapter Скачать руководство пользователя страница 123 | Manualshive

Страница: 123 / 153

background image

Event
ID

Message

Severity

11

E1express:
PROBLEM: Could not allocate memory for receive descriptors.
ACTION: Reduce the number of receive descriptors and restart.

Error

12

E1express:
PROBLEM: Could not allocate memory for receive buffers.
ACTION: Reduce the number of receive descriptors and restart.

Error

13

E1express:
PROBLEM: Could not establish link.
ACTION: Check network cable.

Warning

14

E1express:
  PROBLEM: The PCI BIOS has NOT properly configured the PRO/1000 adapter.
  ACTION: Get the latest BIOS for your computer.
  ACTION: Try another PCI slot.

Error

15

E1express:
  PROBLEM: The PCI BIOS has NOT properly configured the PRO/1000 adapter.
  ACTION: Get the latest BIOS for your computer.
  ACTION: Try another PCI slot.

Error

16

E1express:
  PROBLEM: The PCI BIOS has NOT properly configured the PRO/1000 adapter.
  ACTION: Get the latest BIOS for your computer.
  ACTION: Try another PCI slot.

Error

17

E1express:
  PROBLEM: The PCI BIOS has NOT properly configured the PRO/1000 adapter.
  ACTION: Get the latest BIOS for your computer.
  ACTION: Try another PCI slot.

Error

18

E1express:
  PROBLEM: The PRO/1000 adapter was not configured for bus mastering by the PCI BIOS.
  ACTION: Install the adapter in a bus mastering-capable slot. See your computer doc-
umentation for details.
  ACTION: For more information, run PROSet diagnostics.

Error

19

E1express:
PROBLEM: Could not allocate the NDIS receive packets necessary for operation.
ACTION: Reduce the number of receive descriptors and restart.

Error

20

E1express:
PROBLEM: Could not allocate the NDIS receive buffers necessary for operation.
ACTION: Reduce the number of receive descriptors and restart.

Error

21

E1express:
  PROBLEM: The OS was unable to assign PCI resources to the PRO/1000 adapter.
  ACTION: Move the adapter to another slot.
  ACTION: Remove other hardware that may be causing a conflict.

Error

22

E1express:
PROBLEM: The driver was unable to claim PCI resources of this PRO/1000 adapter.
ACTION: Remove any unused driver instances from the network control panel applet.

NOTE:

Uninstalling any unused network drivers via the control panel may eliminate

this error.

Error

23

E1express:
PROBLEM: The EEPROM on your PRO/1000 adapter may have errors.
ACTION: Visit the support web site at http://support.intel.com/support/network/ for support.

Error

«
...
121
122
123
124
125
...
»

Содержание Ethernet 10G 2P X520 Adapter


























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ethernet 10G 2P X520 Adapter

Бренд: Tamio Страницы: 2

Бренд: X-Micro Страницы: 6

32-bit PCI Fast Ethernet Network Adapter...

Бренд: D-Link Страницы: 16

Therma-Cord TC-2000

Бренд: Radiant Solutions Страницы: 2

SPAS 2400/LC + MU

Бренд: VOLTCRAFT Страницы: 4

WaveBuddy EWP-813WA1

Бренд: 11Wave Technology Страницы: 33

Бренд: Qlogic Страницы: 18

Бренд: Federal Signal Corporation Страницы: 2

Бренд: AccuPower Страницы: 9

Бренд: Supermicro Страницы: 27

Бренд: J-Three Страницы: 10

HomePlug AV 200

Бренд: Gigaset Страницы: 18

Бренд: Asus Страницы: 10

Бренд: Askey Страницы: 3

Бренд: Kvaser Страницы: 24

FCA2214DC PCI-X

Бренд: HP Страницы: 64

Бренд: HP Страницы: 10

Бренд: Salicru Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды