Intel Ethernet 10G 2P X520 Adapter Скачать руководство пользователя страница 128 | Manualshive

Страница: 128 / 153

background image

Event
ID

Message

Severity

38

PROBLEM: The driver failed to initialize properly. You may not be able to change the adapter
settings.
ACTION: Install the latest driver from

http://www.in-

tel.com/support/go/network/adapter/home.htm

.

ACTION: Restart the computer.

Warning

39

PROBLEM: The network adapter driver did not unload successfully.
ACTION: Install the latest driver from

http://www.in-

tel.com/support/go/network/adapter/home.htm

.

ACTION: Restart the computer.

Warning

40

Intel SmartSpeed has downgraded the link speed from the maximum advertised.

Informational

41

The adapter driver has been stopped.

Informational

42

The network adapter driver has been started.

Informational

43

PROBLEM: Could not allocate shared memory necessary for operation.
ACTION: Reduce the number of transmit and receive descriptors, then restart.

Error

44

PROBLEM: Could not allocate memory necessary for operation.
ACTION: Reduce the number of transmit and receive descriptors, then restart.

Error

45

PROBLEM: Could not allocate a resource pool necessary for operation.
ACTION: Reduce the number of transmit and receive descriptors, then restart.

Error

46

PROBLEM: Could not initialize scatter-gather DMA resources necessary for operation.
ACTION: Reduce the number of transmit descriptors and restart.

Error

47

PROBLEM: Could not map the network adapter flash.
ACTION: Install the latest driver from

http://www.in-

tel.com/support/go/network/adapter/home.htm

.

ACTION: Try another slot.

Error

48

PROBLEM: The fan on the network adapter has failed.
ACTION: Power off the machine and replace the network adapter.

Error

49

PROBLEM: The driver was unable to load due to an unsupported SFP+ module installed in
the adapter.
ACTION: Replace the module.
ACTION: Install the latest driver from

http://www.in-

tel.com/support/go/network/adapter/home.htm

.

Error

50

PROBLEM: The network adapter has been stopped because it has overheated.
ACTION: Restart the computer. If the problem persists, power off the computer and replace
the network adapter.

Error

51

PROBLEM: The network adapter link speed was downshifted because it overheated.

Error

52

PROBLEM: The network adapter has been stopped because it has overheated.

Error

53

Jumbo Frames cannot be configured when MACSec is enabled.

Informational

54

PROBLEM: A malicious VF driver has been detected.

NOTE:

This message is used only for the following adapters:

l

Intel® Ethernet X520 10GbE Dual Port KX4 Mezz

l

Intel® Ethernet X520 10GbE Dual Port KX4-KR Mezz

l

Intel® Ethernet Server Adapter X520-2

l

Intel® Ethernet Server Adapter X520-T2

l

Intel® Ethernet 10G 2P X540-t Adapter

Warning

«
...
126
127
128
129
130
...
»

Содержание Ethernet 10G 2P X520 Adapter


























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ethernet 10G 2P X520 Adapter

Бренд: j5 create Страницы: 444

Бренд: Tascam Страницы: 2

Бренд: Rosewill Страницы: 10

Бренд: Aiphone Страницы: 15

Бренд: Davis Instruments Страницы: 4

Бренд: Jabra Страницы: 3

DMXpro LP510-001

Бренд: Synapse Страницы: 21

FM 5 IN DASH ADAPTER KIT

Бренд: Eagle Страницы: 5

Бренд: GodEngine Страницы: 76

Бренд: Bravekit Страницы: 17

Бренд: OBDLink Страницы: 12

Бренд: White Rodgers Страницы: 8

Бренд: Air Live Страницы: 74

Бренд: Zhone Страницы: 1

Бренд: Paradyne Страницы: 1

Бренд: Paradyne Страницы: 31

Бренд: Obihai Страницы: 2

Бренд: Wisenet Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды