Intel Ethernet 10G 2P X520 Adapter Скачать руководство пользователя страница 149

Страница: 149 / 153

Intel® Gigabit Network Daughter Cards

Feature

Intel® Gigabit 4P
X540/I350 rNDC

Intel® Gigabit 4P
X520/I350 rNDC

Intel® Gigabit 4P I350 rNDC

Bus Connector

PCI Express 2.0

Bus Speed

2 x2

Transmission
Mode/Connector

Twisted copper/RJ-45

Cabling

1000Base-T (Category 5)

1000Base-T (Category 5 or Category 3
on 10 Mbps only)

Power Requirements

5.5 Watts (maximum) @ 3.3 V

10.1 Watts (maximum) @ 12 V

5.5 Watts (maximum) @ 3.3 V

Dimensions

(excluding bracket)

5.3 x 2.7 in.
13.5 x 6.9 cm

4.3 x 3.7 in.
11.0 x 9.3 cm

5.3 x 2.7 in.
13.5 x 6.9 cm

Operating Tem-
perature

32 - 131 deg. F
(0 - 55 deg. C)

MTBF

68 years

65 years

117 years

Available Speeds

10/100/1000
auto-negotiate

Duplex Modes

Full or half at 10/100 Mbps; full
only at 1 Gbps

Full or half at 10/100 Mbps; full only at
1000 Mbps

Standards Con-
formance

IEEE 802.1p
IEEE 802.1Q
IEEE 802.3ab
IEEE 802.3ac
IEEE 802.3ad
IEEE 802.3u
IEEE 802.3x
IEEE 802.3z
ACPI v1.0
PCI Express 1.0a

Indicator Lights

Two per port:

Activity and Speed

Two per port:

Activity and Speed

Two per port:

Activity and Speed

Regulatory and
Safety

Safety Compliance

UL 60950 Third Edition- CAN/CSA-C22.2 No.60950-00 (USA/Canada)

EN 60 950 (European Union)

IEC 60 950 (International)

EMC Compliance

FCC Part 15 - Radiated & Conducted Emissions (USA)

ICES-003 - Radiated & Conducted Emissions (Canada)

CISPR 22 - Radiated & Conducted Emissions (International)

EN55022-1998 - Radiated & Conducted Emissions (European Union)

EN55024 - 1998 - (Immunity) (European Union)

CE - EMC Directive (89/336/EEC) (European Union)

VCCI - Radiated & Conducted Emissions (Japan)

CNS13438 - Radiated & Conducted Emissions (Taiwan)

AS/NZS3548 - Radiated & Conducted Emissions (Australia/New Zealand)

MIC notice 1997-41, EMI and MIC notice 1997-42 - EMS (Korea)

Содержание Ethernet 10G 2P X520 Adapter


























































































































































Результаты поиска

Содержание Ethernet 10G 2P X520 Adapter

Отзывы:

Похожие инструкции для Ethernet 10G 2P X520 Adapter

Бренды по названию

Популярные бренды

Intel Ethernet 10G 2P X520 Adapter, Руководство пользователя

Результаты поиска

Содержание Ethernet 10G 2P X520 Adapter

Отзывы:

Похожие инструкции для Ethernet 10G 2P X520 Adapter

Бренды по названию

Популярные бренды