Intel Ethernet 10G 2P X520 Adapter Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 153

background image

With Offloading on, the adapter completes the verification for the operating system.

Default

RX & TX Enabled

Range

l

Disabled

l

RX Enabled

l

TX Enabled

l

RX & TX Enabled

Large Send Offload (IPv4 and IPv6)

Sets the adapter to offload the task of segmenting TCP messages into valid Ethernet frames. The maximum frame size
limit for large send offload is set to 64,000 bytes.

Since the adapter hardware is able to complete data segmentation much faster than operating system software, this fea-
ture may improve transmission performance. In addition, the adapter uses fewer CPU resources.

Default

Enabled; Disabled in Windows Server 2008

Range

l

Enabled

l

Disabled

TCP Checksum Offload (IPv4 and IPv6)

Allows the adapter to verify the TCP checksum of incoming packets and compute the TCP checksum of outgoing pack-
ets. This feature enhances receive and transmit performance and reduces CPU utilization.

With Offloading off, the operating system verifies the TCP checksum.

With Offloading on, the adapter completes the verification for the operating system.

Default

RX & TX Enabled

Range

l

Disabled

l

RX Enabled

l

TX Enabled

l

RX & TX Enabled

UDP Checksum Offload (IPv4 and IPv6)

Allows the adapter to verify the UDP checksum of incoming packets and compute the UDP checksum of outgoing pack-
ets. This feature enhances receive and transmit performance and reduces CPU utilization.

With Offloading off, the operating system verifies the UDP checksum.

With Offloading on, the adapter completes the verification for the operating system.

Default

RX & TX Enabled

Range

l

Disabled

l

RX Enabled

l

TX Enabled

l

RX & TX Enabled

Thermal Monitoring

Adapters and network controllers based on the Intel® Ethernet Controller I350 (and later controllers) can display tem-
perature data and automatically reduce the link speed if the controller temperature gets too hot.

«
...
52
53
54
55
56
...
»

Содержание Ethernet 10G 2P X520 Adapter


























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ethernet 10G 2P X520 Adapter

Бренд: Weego Страницы: 6

Бренд: I-Gard Страницы: 9

Бренд: Mini Gadgets Страницы: 12

Бренд: Addonics Technologies Страницы: 4

Бренд: TP-Link Страницы: 2

Бренд: Syba Страницы: 2

Бренд: Devolo Страницы: 2

Бренд: HQ Страницы: 30

PEPWAVE MAX Adapter

Бренд: peplink Страницы: 20

Бренд: Zeiss Страницы: 6

Бренд: Atheros Страницы: 39

Бренд: Dynex Страницы: 11

Бренд: hager Страницы: 5

Бренд: MSI Страницы: 190

Бренд: Cambium Networks Страницы: 1149

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 24

Бренд: D-Link Страницы: 82

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды