manualshive.com logo in svg

Inivos ProXcide, Руководство пользователя, Страница: 47 / 57

Поделиться
Скачать
Inivos ProXcide Скачать руководство пользователя страница 47

APRIL 2020 • REVISION 4.0 

INSTRUCTION MANUAL

47

Upon completion of a ProXcide™ process a portable gas monitor should be used to check that 

the treatment area is safe to enter. 

It may also be used in the event of process failure, such as due to power failure, to assess when it 

is safe to re-enter the room and investigate the cause of the failure. 

Requirements

1. 

ATI Porta Sens II portable gas leak detector model C 16 or equivalent gas detector.

 

2. 

Hydrogen peroxide sensor with 0 to 20ppm calibration range.

 

Instructions

1. 

Set up the gas leak detector and probe according to the user manual.

2. 

Check that the sensor calibration is in date.

 

3. 

 Switch on the gas leak detector (normally set in continuous reading mode). The screen 

should read 0 ppm.

4. 

 Position the gas leak detector probe tip only into the treatment space either through any 

gap (e.g. door seal) or by slightly opening the door. The main body of the gas leak detector 

and the Operator should remain outside of the treatment space.

 

5. 

Wait until the gas leak detector has stabilised and note the reading.

 

6. 

 If reading is > 2.0ppm then remove the probe and close the door if it is open. Wait 15 

minutes before attempting to re-measure the hydrogen peroxide vapour levels. If reading 

is 1 - 2 ppm then you may enter the room for a maximum of 15 mins / 8 hr period to open 

windows and increase ventilation, before closing the door again and waiting another 15 

minutes. 

7. 

Repeat from step 3 until a safe level of <1ppm is reached. 

Note:

 

In the event of sustained or unusual trends in hydrogen peroxide vapour residue at the end of 

the process, contact the Inivos through the relevent helpline displayed at the bottom of every other 

page. 

 

5.7

 Using a portable gas leak detector

Содержание ProXcide


























































Отзывы:

Нет отзывов