Inivos ProXcide Скачать руководство пользователя страница 20

Страница: 20 / 57

www.

inivos

.com

INSTRUCTION MANUAL

REVISION 4.0 • APRIL

2020

5.1.6

Plug the process monitor mains cable into a convenient electrical socket. Ensure that the

position of the process monitor and power adaptor wires does not cause a trip hazard or

obstruction outside the treatment area. Also ensure the controls and indicators on the monitor

are accessible and visible. You must only use Inivos approved power adapters and cable

extensions.

If significant risk is identified in positioning the monitor just outside of the treatment area

or if there is not an electrical socket available immediately outside the treatment area, then

two options exist. Either plug the process monitor power adaptor in inside the room being

treated and run the power lead under the door, or position the process monitor further afield

in a suitable and safe location where a socket is available, and as close to the treatment area

as possible. Under normal circumstances the wireless communication between the process

monitor and the main unit can reach up to 20 meters, however this depends on the signal

strength and can be a

ected by the fabric of the building and the systems environment.

5.1.7

Extend and plug in the mains cable of the main ProXcide™ unit by grasping and pulling the

mains plug from the base of the main unit. An approved CE marked 13A extension lead may

be used if necessary. If significant risk is identified, it is recommended that the unit is plugged

in outside the room being treated with the power lead being run under the door. This allows

the unit to be fully powered down in the event of a building fire or emergency.

5.1.8

Switch the socket on. The ProXcide™ takes up to one minute to perform baseline checks

and load the system software – Top LED indicators will illuminate

white

. When the system is

booted up and ready to start the top LED indicators will illuminate

blue

Press the top button

on the main unit to connect the main unit to the process monitor. The LED indicators will

illuminate

green

upon successful connection, otherwise it will remain

blue

5.1.9

Present

and hold

your operator card when prompted by the screen following successful

connection of the main unit to the process monitor. This step protects against unauthorised

processes being started. Processes can only be started with an operator card which acts as

a unique key card. If the process monitor has been turned on without first turning on the main

unit, the screen shown below will appear on the process monitor.

5.1.10

Check the system fluid level, which is indicated immediately after switching the socket on.

The fluid level LED indicator is located next to the bottle door and will illuminate

red

if it

requires bottle replacement. The fluid level LED indicator will illuminate

blue

as it slowly fills

up. You must wait for the blue LEDs to reach the top (full). The LED indicators go up or down

depending on the fluid level in the main reservoir tank.

5.1.9

5.1.10

5.1.7

5.1

ProXcide™ Operator Instructions

Содержание ProXcide


























































Результаты поиска

Содержание ProXcide

Отзывы:

Inivos ProXcide, Руководство пользователя, Страница: 20 / 57

Результаты поиска

Содержание ProXcide

Отзывы: