Inivos ProXcide Скачать руководство пользователя страница 11

Страница: 11 / 57

APRIL 2020 • REVISION 4.0

INSTRUCTION MANUAL

Precautions

ProXcin

is a hydrogen peroxide

solution (>5% - <8%) and is classified

as a disinfectant. It is only for use in the

ProXcide

. ProXcin

also contains

≤

0.1%

phosphoric acid and <0.01% silver.

WARNING:

Causes serious eye irritation

WARNING:

Causes skin irritation

    Keep out of reach of children
   Keep in a cool place
    Irritating to eyes, skin and respiratory system
    In case of contact with eyes, rinse

immediately with plenty of water and seek

medical advice

In case of contact with skin, wash

immediately with plenty of water

In case of inhalation, remove the casualty

into fresh air and keep him immobile. If

intensive inhalation of fumes occured seek

medical treatment immediately

Wear suitable personal protective equipment

when handling ProXcin

refills (clothing,

disposable nitrile or butyl gloves and eye/

face protection)

In case of accident or if you feel unwell,

seek medical advice immediately, showing

ProXcin

label or data sheet where possible

Keep away from combustible material

See the material safety data sheets

(MSDS)

for further information, including

what to do in the event of accidental release.

Storage and handling

ProXcin

is delivered in a cardboard outer

containing 4 units weighing a total of

approximately 8.6Kg. Each box is clearly

labeled and contains a MSDS. ProXcin

cartridges should be stored upright in their

sealed container until required for use, in a cool,

ventilated area (not less than 5

C, not more than

C). ProXcin

has no specific legal storage

requirements. However,

our recommendation is

that ProXcin

should

be stored in a bunded

area away from general

public and restricted

to access by trained

ProXcide

Operators

only. Nominated storage

locations should be

communicated to

responsible personnel

within the organisation

including the fire/health

and safety o

icers.

Disposal

Used ProXcin

cartidges should be

disposed of through

an approved waste

disposal facility.

The ProXcide™ uses a low-concentration (7.5%) hydrogen peroxide solution we call ProXcin™.

ProXcin™ is the only approved chemical solution for use in the ProXcide™ and under no

circumstances should it be substituted by any other substance. The low-concentration solution is

compatibile with the hospital environment and patient equipment. The solution is fully-compliant

with the new EU Biocides Directive.

2.4

The ProXcin™ H

solution

Содержание ProXcide


























































Результаты поиска

Содержание ProXcide

Отзывы:

Inivos ProXcide, Руководство пользователя, Страница: 11 / 57

Результаты поиска

Содержание ProXcide

Отзывы: