Inivos ProXcide Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 57

Inivos ProXcide Скачать руководство пользователя страница 26

26

www.

inivos

.com

INSTRUCTION MANUAL

REVISION 4.0 • APRIL

2020

The decontamination cycle status is displayed on the process monitor and gives information about

the cycle phases – injection, dwell and deactivation. All process related information is displayed

on the screen including operator name, process time remaining and any error messages.

While the process is operating, the large LED light panel on the process monitor will glow

red. The colour will only change to green once the deactivation phase is complete.

Screenshots for the di

ff

erent phases of the cycle are given on the following pages:

Decontamination in Process - Injection

Decontamination in Process - Dwell

Deactivation in Process - Deactivation

Process Complete (successful)

Process Complete (unsuccessful)

It is strongly recommended that H2O2 gas concentration tests are performed using a portable gas

leak detector outside of the treatment area doors to check for H2O2 leakage while the process is in

operation, and again as the treatment area is re-entered.
If reading is > 2.0ppm then remove the probe and close the door if it is open. Wait 15 minutes before

attempting to re-measure the hydrogen peroxide vapour levels. If reading is 1 - 2 ppm then you may

enter the room for a maximum of 15 mins / 8 hr period to open windows and increase ventilation,

before closing the door again and waiting another 15 minutes.

Instructions on the use of a gas leak detector can be found in Section 5.7.

5.2

Monitoring the ProXcide™ process

«
...
24
25
26
27
28
...
»

Содержание ProXcide


























































Отзывы:

Нет отзывов