Inivos ProXcide Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 57

Inivos ProXcide Скачать руководство пользователя страница 23

APRIL 2020 • REVISION 4.0

INSTRUCTION MANUAL

23

At this point, make a final check to ensure that all openings are correctly sealed and that smoke

detectors are covered or isolated.

5.1.11

If the main unit indicates correct fluid level in the tank, exit the treatment area through the

remaining unsealed door or temporary barrier.

5.1.12

Close and seal the last door with DVI tape from the outside. Should you miss the low fluid

level indication on the main unit and present your operator card to the process monitor card

reader the system will request a refill by displaying a prompt on the screen with the refill

request. Follow the steps in point 5.1.10 to refill the system.

5.1.13

Follow the on-screen

instructions. Present

your operator card to the

process monitor card

reader. The following

prompts will appear:

‘Location’ - Type in

the process location

using the displayed

keyboard on the

touch screen. Touch

‘YES’ to continue.

5.1

ProXcide™ Operator Instructions

«
...
21
22
23
24
25
...
»

Содержание ProXcide


























































Отзывы:

Нет отзывов