Inivos ProXcide Скачать руководство пользователя страница 38

Страница: 38 / 57

www.

inivos

.com

INSTRUCTION MANUAL

REVISION 4.0 • APRIL

2020

ISSUES

Issue

On-screen description

Explanation

Possible solutions and advice

Forced bottle door

Bottle door appears forced

Temperature Sensor Fault

Temperature sensor

disconnected/broken/not

powered

Humidity Sensor Fault

Humidity sensor

disconnected/broken/not

powered

Fluid calibration. Start

voltage too low.

Fluid sensor voltage not high

enough at start.

Check that the fluid level sensor is plugged in and that

there is fluid all the way up to the bottle cup.

Fluid calibration. Start

voltage not stable

Fluid sensor voltage not

stable at start.

Check that there are no leaks.

Failed to calibrate (drain)

tank in

Fluid sensor voltage didn’t

stabilise.

Check that the tank is empty. Did you connect a container

to empty the tank into? Has the pump failed or is it running

slowly? Are there any restrictions slowing the fluid?

Fluid calibration, voltage

when the tank empty too

high

Fluid sensor reads too high at

the end.

The tank should be empty. Did you connect a container to

empty the tank into? Has the pump failed or is it running

slowly?

Fluid calibration, range too

large

The di

erence between full

and empty is too large.

Is there a leak in the pipe to the sensor (fluid in the pipe)?

Fluid calibration, range too

small

The di

erence between full

and empty is too small.

Is there a leak in the pipe to the sensor (fluid in the pipe)?

Service error. Periodic

service required.

This ProXcide requires service

to operate safely and reliably.

Unable to register with

server

This could be because there

is no 3G signal

Uncontained air volume

ProXcide has injected ProXcin

into the treatment area,

but the humidity has not

increased significantly.

Allow this process to complete fully to the thumbs down

screen, so that you can safely enter the area. To make the

next process a success, please ensure that the room is

fully closed.

Float raised before start

There is a hardware issue

Low fluid

There isn’t enough fluid to

complete the run

Содержание ProXcide


























































Результаты поиска

Содержание ProXcide

Отзывы:

Inivos ProXcide, Руководство пользователя, Страница: 38 / 57

Результаты поиска

Содержание ProXcide

Отзывы: