Inivos ProXcide Скачать руководство пользователя страница 36

Страница: 36 / 57

www.

inivos

.com

INSTRUCTION MANUAL

REVISION 4.0 • APRIL

2020

ISSUES

Issue

On-Screen description

Explanation

Possible solutions and advice

The tank is not full.

- Did you insert a new full

bottle of ProXcin? If not,

please turn main unit o

and

on again to that the bottle

door will open automatically.

DO NOT force the door

open. Replace bottle with

new full bottle. Remember

to push down firmly and

loosen cap.

The tank that holds the

ProXcin solution is not full

enough.

Make sure that a new full bottle of ProXcin is inserted

each time it is automatically requested. If you did not

insert a full bottle, turn the main unit o

/on again and

follow user instructions to replace with a new full bottle. If

it was a new bottle, check:

•

If there are any leaks on the floor

•

If the bottle has been pushed down hard enough and

cap loosened to release the vacuum

Fluid sensor or pump issue

during active operation.

The fluid level is detected by

a sensor, and this may have

fallen. Or the pump may not

be working.

This would occur during active operation and therefore

is present in the room and you must wait for

deactivation to complete.
Check floor for leaks. If there are none, set-up and run the

process again - it may correct itself. If it fails again, contact

Inivos quoting Issue 8 for system swap and repair.

A sensor has failed.

It is safe to enter the room.

Please contact Inivos

quoting issue 12 to arrange

system swap while it is

repaired

This is a hardware issue with

one of the sensors.

This would occur when first powered on, therefore there is

no H

in the room and it is safe to enter. Please contact

Inivos quoting issue 12 to arrange system swap while it is

repaired by us.

Fluid sensor or pump

issue detected during

preparation phase.

Check floor for leaks. If

there are none, set-up and

run the process again - it

may correct itself. If it

fails again, contact Inivos

quoting Issue 13 for system

swap and repair.

The fluid sensor did not rise,

or the fluid was not pumped

into the tank in time.

This would occur during the preparation phase therefore

is not present and it is safe to enter the room.

Check floor for leaks. If there are none, set-up and run the

process again - it may correct itself. If it fails again, contact

Inivos quoting Issue 13 for system swap and repair.

There is a software issue.

An error has occurred in the

software program .

Please contact Inivos quoting issue 14 to arrange system

swap while it is repaired by us.

Содержание ProXcide


























































Результаты поиска

Содержание ProXcide

Отзывы:

Inivos ProXcide, Руководство пользователя, Страница: 36 / 57

Результаты поиска

Содержание ProXcide

Отзывы: