manualshive.com logo in svg

Inivos ProXcide, Руководство пользователя, Страница: 2 / 57

Поделиться
Скачать
Inivos ProXcide Скачать руководство пользователя страница 2

APRIL 2020 • REVISION 4.0 

INSTRUCTION MANUAL

55

9.

 Apply the brakes

10.

  Remove and position the 

process monitor outside 

room

11.

  Extend process monitor 

power cable and plug it in

12.

  Extend main unit power 

cable and plug it in

13.

  Press button on the main 

unit to turn it on. (LED 

white to blue to green)

14.

  Check system fluid level. 

Red means low

15.

  If required, present and 

hold operator card to 

allow door to open

16.

  Replace empty ProXcin 

bottle if required, push 

down, and loosen cap

1.  

Put on your protective 

gloves and eye protection

2.

  Check room has been 

manually cleaned. See 4.3 

in User Manual

3.

  Restrict access - position 

NO-ENTRY signs and 

complete checklist.

4.

  Arrange room contents to 

expose surfaces

5.

  Close and secure all 

doors except one

6.

  Seal gaps in doors and 

windows with DVI Tape

7.

  Cover Vents with VentKit 

and smoke detectors with 

CapKit

8.

  Wheel the main unit into 

the centre of the room

ProXcide Quick Reference Guide

Page 1/2

Notes

Содержание ProXcide


























































Отзывы:

Нет отзывов