Inficon 540-200 Скачать руководство пользователя

Страница: 79 / 90

INFICON

Warning and error messages | 10

T-Guard2_Operating-instructions-jina85en1-13-(2009)

79 / 90

W82

Calibration factor

too high!

If the calibration factor

was set to more than 5,

the calibration was not

successful. If a

calibration factor

between 2 and 5 was

confirmed, a warning

still occurs after

confirming this

successful calibration.

Check the chamber volume

settings and/or gas flow

The calibration leak rate

is smaller than entered.

Check the correct setting for

the calibration leak value!

Chamber volume and/or

gas flow are greater

than entered.

Check the chamber volume

settings and/or gas flow

W84

Calibration leak

signal too small

Calibration leak

defective

Check your calibration leak

Trigger value(s) too

high

Check the trigger

Volume/flow setting too

low

Check the accumulation

volume/the carrier gas flow

Measurement chamber

leaking

Check the measurement

chamber for leaks

W89

Overstep of the limit

value!

The device is

contaminated with

helium.

Do not switch off the device.

Leave the device running

while supplying fresh air to

the measurement and

reference lines until the

warning goes out.

If the warning occurs

frequently, increase the

contamination limit!

Calibration leak value

too high during

calibration

Use a smaller calibration leak

for the calibration!

Содержание 540-200



























































































Результаты поиска

Содержание 540-200

Отзывы:

Похожие инструкции для 540-200

Бренды по названию

Популярные бренды

Inficon 540-200, Перевод оригинальной инструкции по эксплуатации

Результаты поиска

Содержание 540-200

Отзывы:

Похожие инструкции для 540-200

Бренды по названию

Популярные бренды