Inficon 540-200 Скачать руководство пользователя

Страница: 78 / 90

10 | Warning and error messages

INFICON

78 / 90

T-Guard2_Operating-instructions-jina85en1-13-(2009)

If the message occurs

constantly during start-

up, the EEPROM on the

system board is

defective.

Contact INFICON customer

service.

W62

EEPROM

parameters lost!

A parameter was

changed and reset to

factory setting during

the software update.

The parameters

affected are listed in the

warning below.

Check the setting of the

modified parameter in the

corresponding software

menu and set the desired

parameter.

If the message occurs

constantly during start-

up, the EEPROM on the

system board is

defective.

Contact INFICON customer

service.

W64

There are warnings

pending!

Confirmed but not yet

valid warnings are

repeated every two

hours or at every new

start-up.

Check the warnings twice!

W65

Communication

error with fieldbus

module

Switch the device off and

back on. If the problem

persists, contact the

INFICON customer service.

W72

No communication

with analog card

Switch the device off and

back on. If the problem

persists, contact the

INFICON customer service.

W81

Calibration factor

too low!

If the calibration factor

was set to less than 0.2,

the calibration was not

successful. If a

calibration factor

between 0.2 and 0.5

was confirmed, a

warning still occurs after

confirming this

successful calibration.

The calibration leak rate

is larger than entered.

Check the correct setting for

the calibration leak value!

Содержание 540-200



























































































Результаты поиска

Содержание 540-200

Отзывы:

Похожие инструкции для 540-200

Бренды по названию

Популярные бренды

Inficon 540-200, Перевод оригинальной инструкции по эксплуатации

Результаты поиска

Содержание 540-200

Отзывы:

Похожие инструкции для 540-200

Бренды по названию

Популярные бренды