Inficon 540-200 Скачать руководство пользователя

Страница: 23 / 90

INFICON

Installation | 5

T-Guard2_Operating-instructions-jina85en1-13-(2009)

23 / 90

5 Installation

5.1 Setup

WARNING

Danger from moisture and electricity

Moisture entering the device can lead to personal injury due to electric shocks as well

as damage to property due to short circuiting.

► Only operate the device in dry environments and only in buildings.

► Operate the device away from sources of liquid and moisture.

► Position the device so that you can always reach the plug for unplugging.

► Do not operate the device in standing water and do not allow even a drop of water

or other liquid on the device.

► Prevent the device from coming into contact with bases, acids and solvents.

CAUTION

Danger due to dropping heavy loads

The device is heavy and can damage persons and items through tilting or dropping.

► Have the overhead installation carried out by qualified personnel only.

► Use suitable fixing material.

► Only place the device on a sufficiently sturdy surface.

NOTICE

Property damage due to overheated device

The device heats up during operation and can overheat without sufficient ventilation.

► Please note the technical specifications.

► Ensure adequate ventilation. There must be 20 cm of free space on the upper side

of the device above the ventilation opening.

► The ventilation opening on the underside of the device must remain unobstructed.

► Keep heat sources away from the device.

► Do not expose the device to direct sunlight.

There must be no vibrations affecting the device. Vibrations can lead to incorrect

measurement results.

Содержание 540-200



























































































Результаты поиска

Содержание 540-200

Отзывы:

Похожие инструкции для 540-200

Бренды по названию

Популярные бренды

Inficon 540-200, Перевод оригинальной инструкции по эксплуатации

Результаты поиска

Содержание 540-200

Отзывы:

Похожие инструкции для 540-200

Бренды по названию

Популярные бренды