Inficon 540-200 Скачать руководство пользователя

Страница: 9 / 90

INFICON

Safety | 2

T-Guard2_Operating-instructions-jina85en1-13-(2009)

9 / 90

2.4 Dangers

The measuring instrument was built according to the state-of-the-art and the

recognized safety regulations. Nevertheless, improper use may result in risk to life and

limb on the part of the user or third parties, or damage to the unit or other property

may occur.

Dangers from electric

power

The device is operated with electrical voltages of up to 24 V. Inside the device there

are voltages that are considerably higher. There is a danger to life from the contact of

conductive parts inside the device.

• Disconnect the device from the power supply prior to any installation and

maintenance work. Make sure that the electric power supply cannot reconnected

without authorization.

• Before starting the leak test, disconnect electrically operated test objects from the

power supply.

The device contains electric components that can be damaged from high electric

voltage.

• Make sure before connecting to the power supply that the supply voltage is 24 V

+/- 16 % (stabilized!).

Hazards due to liquids

and chemicals

Liquids and chemical substances can damage the instrument.

• Do not suck up liquids with the instrument.

• Never try to find toxic, caustic, microbiological, explosive, radioactive or other

harmful substances with the device.

• Only operate the device in a dry environment.

• Only use the device away from areas with a risk of explosions.

• No smoking. Do not subject the device to open fire and avoid sparking.

Содержание 540-200



























































































Результаты поиска

Содержание 540-200

Отзывы:

Похожие инструкции для 540-200

Бренды по названию

Популярные бренды

Inficon 540-200, Перевод оригинальной инструкции по эксплуатации

Результаты поиска

Содержание 540-200

Отзывы:

Похожие инструкции для 540-200

Бренды по названию

Популярные бренды