manualshive.com logo in svg

Impacts S210E, Руководство по эксплуатации

Поделиться
Скачать
Impacts S210E Скачать руководство пользователя страница 26

S210E

Operating Manual

24

6.5 

Restarting after a Fault

After a fault make sure that you find the reason of the fault before you restart the machine. Leave the 
emergency switch pushed down and bring the machine in the safety-off position before you start to 
find out the fault.

If you do not find the fault or if you are unsure about the reason for the fault, please contact your 
IMPACTS contact person and ask for help.

Please consider special regulations in VBG 4 and VDE-0701.These regulations 
describe the necessary considerations and actions after repairing and changing 
electrical Equipment. For start up of the machine, see chapter 5.

6.5 

Proceedings Prior and After Longer Stoppage

Stoppage Longer Than 3 Months:

•  Switch off the machine (see Chapter 6).

•  Remove all abrasive out of the machine.

•  Remove all abrasive from magnets.

•  Clean the machine and cover with a tarp in a dry area.

•  Ensure that motors, cables, and plugs are protected against moisture, dust, heat, and shock.

•  Protect bright parts of the machine and power pack with a preservative oil or grease.

After Longer Stoppage:

•  See Chapter 5 "Initial Operation."

Содержание S210E

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды