IHI IC50 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 104

background image

OPERATION

IC50 ENG

3-8

Steering control

Gentle turn

Change the stroke of the travel lever (1) or (2) to change
the travel direction while moving forward (or backward).
Return the lever of the desired direction slightly. The
machine turns in that direction slowly.

Pivot Turn

•

Move the right travel lever (1) forward, allowing the

machine to the left, pivoting on the left track.

•

Move the left travel lever (2) forward, allowing the

machine to turn to the right, pivoting o the right track.

Spot Turn

•

Move the right side travel lever (1) forward and move

the left side travel lever (2) backward at the same time.
This allows a quick left turn (counter track rotation).

•

Move the right side travel lever (1) backward and move

the left side travel lever (2) forward at the same time.
This allows a quick right turn (counter track rotation).

WARNING

NEVER steer on a grade or unstable ground, which
causes turnover. It is very dangerous.
If the engine stall when changing directions while
the engine speed is low or the travel select switch
is set to high. Restart the engine, increase the
engine speed and set the travel select lever is set
to low. Avoid the engine stall to control the travel
levers stroke while travelling.
Never change the travel direction quickly on a
slope. Quick direction change may cause turnover
or slip.
If it is necessary to change the travel direction
quickly, move to a solid ground with a gentle slope
and change the direction.

Travel lever

Pivot left turn

Forward left

turn

Backward left

turn

Pivot right turn

Forward right

turn Backward

right

turn

Spot turn

«
...
46
47
48
49
50
...
»

Содержание IC50









































































































Отзывы:

Нет отзывов

Похожие инструкции для IC50

665.1473 series

Бренд: Kenmore Страницы: 40

665.1361 Series

Бренд: Kenmore Страницы: 44

665.1472 Series

Бренд: Kenmore Страницы: 44

Бренд: Ditch Witch Страницы: 199

Бренд: Toro Страницы: 11

Бренд: Toro Страницы: 40

TLB25-35BV Series

Бренд: Scag Power Equipment Страницы: 38

Бренд: SDLG Страницы: 782

Бренд: Krushr Страницы: 34

Бренд: Greyhound Страницы: 61

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды