background image

OPERATION 

IC50 ENG 

3-14 

AVOID SUDDEN CHANGES IN DIRECTION WHEN 
STEERING 

  Make direction changes in several smaller steering 

movements.  

  Avoid sudden changes in direction. 

This causes early wear on the lug and may cause the 
crawlers to slip off. 

 
 

DO NOT TRAVEL OVER HIGH HEAT LOCATIONS. 

Do not try to travel over place subjected to high heat such 
as steel plate that was placed in bonfires or under 
scorching heat, asphalt or floorboards etc. 
This causes serious abrasion or damage and breakage of 
the lug. 
 
 

OTHER ITEMS FOR CAUTION 

 

DO NOT LET OIL – SOLVENTS OR SALT ADHERE TO 
THE RUBBER CRAWLERS 

  If fuel, transmission fluid or paint should adhere to the 

rubber crawlers wipe it away quickly. 

  Wash away with water after working in locations with a 

large salt content.  Salt can cause the iron core to rust 
or peel. 

 
 

ALWAYS USE CORRECT TENSION ON THE SHOE 

Attempting to change directions on terrain with different 
levels or steps while the rubber crawler is still slack may 
damage the rubber crawlers or cause them to come off 
the rollers. 
 

Upper roller

Oil 

Solvent

Salt

Clearance 

Idler

Содержание IC50









































































































Отзывы: