IHI IC50 Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 104

background image

MAINTENANCE

IC50 ENG

4-3

PERIODICAL EXCHANGE OF THE IMPORTANT PARTS

Carry out periodical maintenance of the parts shown below having great concern with safety and
fire, in particular.
These parts are subject to changes of materials, wear and deterioration as they are used long. It
is difficult to judge the service life by checking the appearance of these parts. Replace them
periodically, even though they do not have apparent defects.

Fuel relation

Parts to be replaced periodically

Q’ty

Replace interval

Fuel hose (between fuel tank and fuel pre-filter)

1

Fuel hose (between fuel pre-filter and electromagnetic fuel pump)

1

Fuel hose (between electromagnetic fuel pump and fuel main

filter)

1

Fuel hose (between fuel main filter and engine)

1

Fuel hose (between engine and fuel cooler)

1

Fuel hose (between fuel cooler and fuel tank)

1

Every 2 years

Hydraulic relation

Parts to be replaced periodically

Q’ty

Replace interval

Hydraulic hose (between pump and right travel motor, main line)

2

Hydraulic hose (between pump and left travel motor, main line)

2

Hydraulic hose (between pump, CV and dump cylinder)

7

Every 2 years

Repair or replace these parts immediately if some abnormalities or defects are found in them
even before the replacement periods.
Also check the fuel hoses and hydraulic hoses in daily check, monthly check and yearly check.

«
...
61
62
63
64
65
...
»

Содержание IC50









































































































Отзывы:

Нет отзывов

Похожие инструкции для IC50

Бренд: GE Страницы: 24

Бренд: Hyundai Страницы: 41

Бренд: Takeuchi Страницы: 182

Бренд: P.Lindberg Страницы: 97

Бренд: Barreto Страницы: 28

Бренд: RAMROD Страницы: 34

Sitework Systems 22420

Бренд: Toro Страницы: 12

Бренд: NuTone Страницы: 8

Mikasa MVH-702DRSC

Бренд: MULTIQUIP Страницы: 58

Бренд: AVANT Страницы: 16

Бренд: AVANT Страницы: 24

Бренд: AVANT Страницы: 24

Бренд: AVANT Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды