IHI IC50 Скачать руководство пользователя страница 47

Страница: 47 / 104

OPERATION

IC50 ENG

3-7

TRAVELING THE MACHINE

Start-travel-stop

WARNING

•

When traveling, lower the body completely.

•

Lock the rear gate and side gates firmly.

•

Make sure that no persons are around the

machine. Sound the horn before starting.

1. Adjust the traveling speed properly with the travel

speed select switch (1). (See page 2-7)

2. Turn the engine throttle dial to increase the engine

speed to the necessary speed.

3. Push down on the no-mark position of the parking

switch (2) to deactivate the brake.
Make sure that the mark lamp is off.

4. Use the right and left travel levers (3) and (4) as shown

below.

•

Forward direction travel

Push the right and left levers (3) and (4) evenly and
slowly to start the machine slowly.

•

Backward direction travel

Pull the right and left levers (3) and (4) evenly and
slowly to start the machine slowly.

•

Speed adjustment

Increase the travel lever stroke to raise the speed.
Decrease the stroke to reduce the speed.

5. Stopping

Set the right and left levers (3) and (4) to the neutral
position. The machine stops and the travel brake is
applied automatically.

Forward

Backward

Forward

Содержание IC50









































































































Результаты поиска

Содержание IC50

Отзывы:

IHI IC50, Руководство по эксплуатации, Страница: 47 / 104

Результаты поиска

Содержание IC50

Отзывы: